Gemalto Cinterion PLS62T-W USB Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 91

background image

Cinterion

®

Java Terminal Hardware Interface Description

3.8 GPIO Interface

40



PLS62T-W_HID_v01

2018-06-20

Confidential / Prelimenary

Page 30 of 91

Please refer to the “AT Command Set“ for details on how to configure the GPIO pins using AT
commands.

3.8.1

Serial Interface ASC1

The Java Terminal has four pins at the GPIO connector which can be configured as ASC1 in-
terface signals to provide a 2- or 4-wire serial modem interface ASC1. For electrical character-
istics please refer to

.

The following pins at the GPIO connector can be configured as ASC1 interface signals: RXD1,
TXD1, RTS1 and CTS1 (see also

). The configuration is done by AT command

AT^SCFG - see

. It is non-volatile and becomes active after a Java Terminal restart.

Java Terminal are designed for use as a DCE. Based on the conventions for DCE-DTE con-
nections they communicate with the customer application (DTE) using the following signals:
•

Port TXD @ application sends data to Java Terminal’s TXD1 signal line

•

Port RXD @ application receives data from the Java Terminal’s RXD1 signal line

12-pin connector

1

VCCref

Input supply for level adjustment. E.g., connect
+5Vout for 5V IO operation



2

GND



3

GPIO17,
TXD1 or
SPI_MISO

Configurable via AT command, GPIO or TXD1
(RS-232) or
SPI_MISO signal

GPIO17 /TXD1 /SPI_MISO

4

GPIO16,
RXD1 or
SPI_MOSI

Configurable via AT command, GPIO, RXD1 (RS-
232) or
SPI_MOSI signal

GPIO16 /RXD1 /SPI_MOSI

5

GPIO19,
CTS1 or
SPI_CS

Configurable via AT command, GPIO, CTS1 (RS-
232) or SPI_CS signal

GPIO19 /CTS1 /SPI_CS

6

GPIO18 or
RTS1

Configurable via AT command, GPIO or RTS1
(RS-232) signal

GPIO18 /RTS1

7

+5Vout

External power supply up to 100mA, usable as
VCCref input



8

DSR0,
GPIO3 or
SPI_CLK

Configurable via AT command

DSR0 /GPIO3 /RTS1

9

I2CDAT

I

2

C interface



10

I2CCLK

I

2

C interface



11

GPIO20

Configurable via AT command



12

GPIO21

Configurable via AT command



Table 14:

GPIO connector pin availability and alternate pin functionalities

PIN

Signal

Comment

PLS62T-W

«
...
28
29
30
31
32
...
»

Содержание Cinterion PLS62T-W USB




























































































Отзывы:

Нет отзывов

Похожие инструкции для Cinterion PLS62T-W USB

Бренд: BACtrack Страницы: 13

Бренд: TA Instruments Страницы: 35

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Sonopuls HD 4050

Бренд: BANDELIN Страницы: 48

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Haas Страницы: 12

Бренд: SaMASZ Страницы: 25

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 11

Бренд: ABB Страницы: 4

FUSION APOLLO MS-WB675

Бренд: Garmin Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды