manualshive.com logo in svg

Geely MK Series, Руководство пользователя

Поделиться
Скачать
Geely MK Series Скачать руководство пользователя страница 106

Warning

Warning

32. Tilt the Steering Wheel.

To change the angle of the steering wheel, you 
can hold the steering wheel and press down the 
tilt adjustment handle to tilt the steering wheel 
to a desired angle, then restore the adjustment 
handle to its original position. 

The cup holder is used for holding the cup or 
beverage can.

Do not put any thing other than the cup 
and beverage can, otherwise it would 
be thrown off and cause body injury in 
case of emergent brake or acciden.

  

Do not adjust the steering wheel 

when the vehicle is moving because 
that may result in unexpected ac-
cidents or even body injuries or death 
due to improper operation of the 
vehicle.   

  

After the adjustment of the steering 

wheel, move it up and down to make 
sure it is duly locked in place. 

99

Part I

Содержание MK Series





























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды