GEDA MAXI 120 S Скачать руководство пользователя страница 70

Страница: 70 / 90

Maintenance - Checking - Cleaning

GEDA

MINI 60 S / MAXI 120 S / MAXI 150 S

Assembly and Operating Manual

70 / 90

BL068 GB Edition 03/2015

8.3.3

Checking / replacing the wire rope

Check the rope for signs of damage and wear (e.g. wire breaks,
pinched points, looping of wires) and corrosion (refer to DIN 15020
Part 2), if necessary replace the rope.



In the event of wire breaks, the wire rope must be replaced at the
latest after more than 8 wires are broken over a length of 135 mm
[5.31

″].

Replacing the wire rope

Disassembly from the rope drum

For better access to the rope drum
when replacing the rope, remove
the rope cylinder (5) on the flexible
drum guard.



Unwind the wire rope (1) up to the last two coils.



Loosen the cable clamp by loos-

ening the central screw (4) in the
main shaft.



First pull the wire rope (1) out of

the clamping position (3), then
from the drum feed-through (2a)
(push back the rope so that it re-
laxes).

Assembly on the rope drum



First place the wire rope (1)

through the drum feed-through
(2a).



Push through by approx. 1 m [3.3 ft) and place in the last two outer

rope grooves (2b).



Place the wire rope (1) in the hole at the clamping position (3) until it

is visible from the opposite side (3a).



Use the central screw (4) and clamp the rope in the drive shaft.



Pull both loose rope coils (2b) fully tight.



Install the rope cylinder (5).



Coil the cable cleanly on the drum.

Содержание MAXI 120 S



























































































Результаты поиска

Содержание MAXI 120 S

Отзывы:

Похожие инструкции для MAXI 120 S

Бренды по названию

Популярные бренды

GEDA MAXI 120 S, Сборка и руководство по эксплуатации

Результаты поиска

Содержание MAXI 120 S

Отзывы:

Похожие инструкции для MAXI 120 S

Бренды по названию

Популярные бренды