background image

II. 

Safety Instructions 

 
 
1.

 

Read all instructions before operation.  Retain instructions for your permanent records. 

 
2.

 

Disconnect power source before servicing or cleaning unit.   

 
3.

 

Do not permit unauthorized personnel to operate the unit at any time. 

 
4.

 

Do not pull alcohol or other combustible materials in the vacuum tank. 

 
5.

 

Never operate vacuum at pressures or speeds in excess of those recommended by 
manufacturer. 

 
6.

 

Some elements on the unit may be quite warm in normal operation.  Do not touch or 
permit combustible materials to come in contact with these components. 

 
7.

 

Do not touch moving parts while the Dropmaster is in service. 

 
8.

 

Technician operating the Dropmaster should utilize eye and hearing 
protection at all times. 

 
9.

 

Unit should be operated in a clean and well-ventilated area. 

 
10. 

The Dropmaster is to be used for siphoning water or non-combustible antifreeze from fire 
sprinkler systems, boilers, heat exchangers, chillers, or similar types of piping systems. 

 
11.     Use caution when transporting Dropmaster unit, make sure unit is properly 
          secured in transporting vehicle. Transport unit in the upright position. 
 
12. 

Please note separate safety instructions are enclosed for the vacuum pump used in the 
Dropmaster.  This must be reviewed before operating Dropmaster. 

 

 
 
 
 
 
 
 
 

-3- 

Содержание Dropmaster DM12


















Отзывы: