GeBe Powerman 3000i Скачать руководство пользователя

Страница: 28 / 36

English

SPARK PLUG INSPECTION

The spark plug is important

engine components,

which should be checked

periodically.

1. Remove the cap (1) and

spark plug cap (2),Insert

the tool (4) through the

hole from the outside of the

cover.

2. Insert the handlebar (3)

in to the tool (4) and turn it

counter clockwise to remove

the spark plug.

3. Check for discoloration

and remove any carbon

deposits. The porcelain

insulator around the center

electrode of spark should be

4. Check the spark plug

type and gap

Spark plug type:

E6RTC

NGK: BPR6HS

CHAMPION: RL87YC

DENSO: W16FRP

BOSCH: WR6BC

BERU: Z19

Gap: 0,6-0,7mm

(0,024-0,028in)

5. Install the spark plug

6. Install the spark plug cap

and spark plug cover.

TIP: If a torque wrench is not available when

installing a spark plug, a good estimate of the correct

torque is 1/4-1/2 turn past finger tight. However,

the spark plug should be tightened to the specified

torque as soon as possible.

CARBURETOR ADJUSTMENT

The carburetor is a vital part of the engine. Adjusting

should be left to a dealer with the professional

knowledge, specialized date, and equipment to do so

properly.

ENGINE OIL REPLACEMENT

Avoid draining the engine oil immediately after

stopping the engine. The oil is hot and should be

handled with care to avoid burns.

1. Place the generator on

a level surface and warm

up the engine for several

minutes. Stop the engine

and turn the 3 in 1 switch

knob and fuel tank cap air

vent knob to “OFF”.

2. Remove the screw (1)

and then remove the

cover (2).

3. Remove the oil filler

cap (3).

4. Place an oil pan under

the engine. Tilt the

generator to drain the oil

completely.

5. Place the generator to a

level surface

Do not tilt the generator

when adding engine oil. This

could result in overfilling

and damage to the engine.

6. Add engine oil to the

upper level. (Chek page xx)

7. Wipe the cover clean,

and wipe up any spilled oil.

Be sure no foreign material

enters the crankcase.

8. Install the oil filler cap.

9. Install the cover and

tighten the screws.

AIR FILTER

1. Remove the screw (1) and then remove the cover

(2).

2. Remove the screw (3) and then remove the air

filter case cover (4).

3. Remove the foam element .

4. Wash the foam element in solvent and dry it.

5. Oil the foam element and squeeze out excess oil.

The foam element should be wet but not dripping

Содержание Powerman 3000i





































Результаты поиска

Содержание Powerman 3000i

Отзывы:

Похожие инструкции для Powerman 3000i

Бренды по названию

Популярные бренды

GeBe Powerman 3000i, Руководство пользователя

Результаты поиска

Содержание Powerman 3000i

Отзывы:

Похожие инструкции для Powerman 3000i

Бренды по названию

Популярные бренды