manualshive.com logo in svg

GEAppliances gdwt708vbb, Руководство по установке, Страница: 8 / 12

Поделиться
Скачать
GEAppliances gdwt708vbb Скачать руководство пользователя страница 8

Check

Level
Side-

to-Side

Check

Level

Front-

to-Back

 

STEP 11  LEVEL DISHWASHER

IMPORTANT

 –  Dishwasher must be level

for proper dish rack operation and wash performance.

• Place level on door and rack track as shown. Check to

make sure that the dishwasher is level.

• Level the dishwasher by adjusting the four leveling

legs individually.

• If adjustment to the right rear leveling leg is re-

quired, loosen junction box bracket screw (through
the access hole) and rotate bracket clockwise.

Tip: 

Pull lower rack out, about halfway. Check to be

sure the rack does not roll forward or back into
dishwasher. If the rack rolls in either direction, the
dishwasher must be leveled again.
• If door hits tub, the dishwasher is not installed

correctly. Adjust leveling legs to align door to tub.

Installation Instructions

8

STEP 10  PUSH DISHWASHER

INTO FINAL POSITION

Tip:

 

Check tub insulation blanket, if equipped. It

should be positioned so it is not “bunched up” or
interfering with door springs. Check by opening and
closing door.
• Push dishwasher into the cabinet. The edges of the

dishwasher door should be behind the cabinet
frame and evenly aligned with the front face of
cabinet doors.

• Carefully open and close the door to ensure the

door panel is not catching or rubbing on the
cabinet frame.

Figure Q

Door

Fits and

Swings

Back

Behind

Cabinet

Frame

Correct

Alignment

Door Catches

on Cabinet Frame

Incorrect

Alignment

Figure R

STEP 9A  INSTALL SIDE-MOUNT

BRACKETS (included with
some models)

Skip this step if underside of countertop is wood or
wood-like material.

• Install side-mount brackets if underside of countertop

is granite or similar material that will not accept
wood screws. The bracket kit is located in the
Owner’s Manual bag on models with this feature.

Note: 

 The brackets are available for purchase when

needed for models not factory equipped with the side-
mount kit. Order part GPF65 from your authorized GE
Appliance Dealer.

• Fasten the left-hand bracket to the left side of the

dishwasher frame. Fasten the right-
hand bracket to the right side
of the dishwasher frame,
using the #8 pan-head
screws included with the kit.
Refer to Step 12, Figure U for
orientation and placement.

Figure S

Side-Mounting Brackets

on some models

Turn Legs

to Adjust

Access Hole

J. Box

Содержание gdwt708vbb













Отзывы:

Нет отзывов