GEAppliances gdwt708vbb Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 12

GEAppliances gdwt708vbb Скачать руководство пользователя страница 5

Installation Instructions

5

Figure G

STEP 1 CHECK DOOR BALANCE

With dishwasher on wood skid, check the door balance
by opening and closing the door.
• If door drops open when released, increase spring

tension. If door closes when released, decrease
tension.

Note:

Increase or decrease

tension as shown. Adjust
both springs to the same
tension setting to correct
balance.

Tip:

If door spring adjustment is necessary, check door

opening and closing. If door does not open easily or
falls too quickly, check spring cable routing. The cable
is held in place by “shoulders” on the pulley. Check to
be sure cable has not slipped over the pulley shoulders.

PREPARE HOT WATER LINE

• The line may enter from either side, rear or floor

within the shaded area shown in Figure F.

• The line may pass through the same hole as the

electrical cable and drain hose. Or, cut an additional
1-1/2" dia. hole to accommodate the water line. If
power cord with plug is used, water line must not
pass through power cord hole.

6"

5"

5"

4"

Cabinet Face

Shut-off
Valve

4"

2" From Floor

19" From Wall

2"

From

Cabinet

1-1/2" Dia.

Hole

Hot

Figure F

Water Line Connection

• Turn off the water supply.
• Install a hand shut-off valve in an accessible location,

such as under the sink. (Optional, but strongly recom-
mended and may be required by local codes.)

• Water connection is on the left side of the dishwasher.

Install the hot water inlet line, using no less than 3/8"
O.D. copper tubing. Route the line as shown in Figure F
and extend forward at least 19" from rear wall.

• Adjust water heater for 120

°

F to 150

°

F temperature.

• Flush water line to clean out debris.
• The hot water supply line pressure must be 20-120 PSI.

Increase

Spring

Tension

Decrease

Spring

Tension

Insert

Hook

Over

Bracket

Correct

Incorrect

• Screw leveling legs back into the dishwasher

frame, approximately 1/4" from frame as shown.

Figure H

STEP 2 REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT

–

Do not kick off wood base!

Damage will occur.

• Move the dishwasher close to the installation

location and lay it on its back.

• Remove the four leveling legs on the underside of

the wood base with an adjustable
wrench or 15/16" socket.

• Discard base.

Approx.

1/4"

CAUTION:

Do not remove wood base until you are

ready to install the dishwasher. The dishwasher will tip
over when the door is opened .

BEFORE YOU BEGIN

Locate and set aside (for use in Step 12) the
2 Phillips special head screws wrapped with

yellow tape and stuck to the top or side of the dish-
washer. Remove drain hose from upper rack, if it has
not been pre-installed, and set aside for use in Step 5A.

«
...
3
4
5
6
7
...
»

Содержание gdwt708vbb













Отзывы:

Нет отзывов