manualshive.com logo in svg

GEAppliances gdwt708vbb, Руководство по установке, Страница: 12 / 12

Поделиться
Скачать
GEAppliances gdwt708vbb Скачать руководство пользователя страница 12

Pub. No. 31-30579
Dwg. No. 206C1559P119

N.D. 923-02 (2/04)  Rev. 1

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

• Align the toekick with the bottom edge and make

sure it is against the floor.

• Insert and tighten the two toekick attachment

screws. The toekick should stay in contact with the
floor.

Tip:

 Make sure toekick is against floor to minimize

noise.

Figure CC

STEP 19  LITERATURE

• Be sure to leave complete literature package and

Installation Instructions with the consumer.

STEP 18  REPLACE TOEKICK

• Place toekick against the legs of the dishwasher.

Installation Instructions

STEP 17 

  DISHWASHER WET TEST

 Turn on power supply (or plug power cord into

outlet, if equipped).

 Latch door.

 Push “Rinse Only” button.

 Push start/reset pad once. Dishwasher should start.

 Check to be sure that water enters the dishwasher.

If water does not enter the dishwasher, check to be
sure that water and power is turned on.

 Check for leaks under the dishwasher. If leak is

found, turn power supply off, then tighten connec-
tions. Restore power after leak is corrected.

 Check for leaks around the door. A leak around the

door could be caused by door rubbing or hitting
against adjacent cabinets. Reposition the dish-
washer if necessary. See Step 12.

 The dishwasher will drain and turn off about 5

minutes after it was started. Check drain lines. If
leaks are found, turn power off at the breaker,
correct as necessary. Restore power after correc-
tions are made. See Step 5A and 14.

 Open dishwasher door and make sure most of the

water has drained. If not, check that disposer plug
has been removed and/or air gap is not plugged.
See Step 14.

 Press Start/Reset pad once again and run dish-

washer through another “Rinse Only” cycle. Check
for leaks and correct if required.

Toekick

Attachment Screws

Содержание gdwt708vbb













Отзывы:

Нет отзывов