manualshive.com logo in svg

GEA Hilge HYGIA ADAPTA, Руководство по эксплуатации

Поделиться
Скачать
GEA Hilge HYGIA ADAPTA Скачать руководство пользователя страница 12

2.3

Explanation of the safety symbols used

Danger

 

Stands for an immediate danger which leads to heavy physical injuries or to
the death.
► Description to avert the danger

Warning!

 

Stands for a possibly dangerous situation which leads to heavy physical
injuries or to the death.
► Description to avert the dangerous situation.

Caution!

 

Stands for a possibly dangerous situation which could lead to light physical
injuries or to damages to property.
► Description to avert the dangerous situation.

 

Notice!

 

Stands for an important tip whose attention is important for the designated
use and function of the product.
► Description of the necessary action for proper operation of the product.

2.4

Safety instructions for the company/operator

Follow the safety instructions contained in this operating manual, the relevant
national accident prevention regulations as well as any internal working,
operating, and safety provisions of the operating company.

Warning!

 

Hot or cold machine parts

Risk of burns.
► Secure hot or cold machine parts against contact!

Warning!

 

Rotating machine parts

Hazard of entrapment or entanglement.
► Do not remove contact protection for rotating machine parts (e.g.
coupling)!
► Replace defective safety devices promptly!

Safety

Explanation of the safety symbols used

 

BA.H2A.ADY.002.GB_1

12

18.12.2017

Содержание Hilge HYGIA ADAPTA

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды