background image

Technical data: Ambient temperatures

Designation

Description

- Control top type T.VIS M-15, A-15

-20 to +50 °C (-4 ... +122 °F)

- Control top type T.VIS P-15

0 to +50 °C (-4 ... +122 °F)

Product and operating temperature

-40 to +135°C

Technical data: Compressed air supply

Designation

Description

Air hose

- metric

Material PE-LD outside Ø 6 mm
Inside Ø 4 mm

- Inch

Material PA outside-Ø 6.35 mm
Inside Ø 4.3 mm

Product pressure

max. 10 bar (116 psi)

Control air pressure

min. 4.8 bar
max. 8 bar

Control air pressure for air/air - A/A
actuator

min. 4.0 bar
max. 8 bar

Control air

acc. to ISO 8573

- Solid particle content:

Quality class 6
Particle size max. 5 µm
Particle density max. 5 mg/m

3

- Water content:

Quality class 4 max. dew point +3 °C
If the unit is used at higher altitudes or
at low ambient temperatures, the dew
point must be adapted accordingly.

- Oil content:

Quality class 3, ideally oil-free, max.
1 mg oil for 1 m

3

 air

Air requirement per switching operation

Actuator type

Actuator diameter [mm]

Air requirement (dm

3

 

n

/

stroke)
dm

3

 

n

 with 1.01325 bar

at 0 °C as per DIN 1343

"DN 50, DN 65 2" OD,
2.5" OD"

88.9

0.325

"DN 80, DN 100 3" OD,
4" OD"

114.3

0.530

Technical data

Technical data

 

430BAL010337EN_7

24

29.07.2021

Содержание ECOspace



































































Отзывы: