GEA ECOspace страница 14 Скачать руководство пользователя

Страница: 14 / 66

The signs and notes on the valve must always be legible. Any illegible signs must
be replaced immediately.

Signs on the valve

Sign

Meaning

Fig.1

General hazard warning

Fig.2

Warning Crushing

Fig.3

Explosive atmosphere hazard warning

2.8

Residual dangers

Dangerous situations can be avoided by safety-conscious and proactive
behaviour of the personnel and by wearing personal protective equipment.

Residual dangers on the valve and measures

Danger

Cause

Measure

Danger to life

Inadvertent switch-on of the
valve

Effectively disconnect all components, effectively prevent switch-
on.

Electric power

Observe the following safety rules:

Isolate from the power supply.

Take appropriate measures to prevent switch on.

Test absence of voltage.

Earthing and short-circuiting.

Cover or safeguard any adjacent live parts.

Spring tension in the actuator

Danger to life caused by compression spring in the actuator. Do
not open the actuator but return it to GEA Tuchenhagen for
proper disposal.

Safety

Residual dangers

430BAL010337EN_7

29.07.2021

Содержание ECOspace



































































Результаты поиска

Содержание ECOspace

Отзывы:

Похожие инструкции для ECOspace

Бренды по названию

Популярные бренды

GEA ECOspace, Инструкция по эксплуатации

Результаты поиска

Содержание ECOspace

Отзывы:

Похожие инструкции для ECOspace

Бренды по названию

Популярные бренды