GE ZBD1870NSS Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 14

GE ZBD1870NSS Скачать руководство пользователя страница 8

90

°

Elbow

Fill

Hose

Thread

Seal Tape

Water

Valve

Bracket

White

Ground

Black

Check That White, Black and

Green Dishwasher Wires Are Threaded

Thru Hole in Back

Remove

Junction Box

Cover

Insert Power

Cord Wires Thru

Strain Relief

and Tighten

Use UL Listed

Wire Nuts

A

C

B

D

Installation Instructions

STEP 2 ADJUST LEVELING LEGS

• Move the dishwasher close to the installation location and lay

it on its back.

Figure L

• Measure installation height and dishwasher height. Extend

leveling legs out from the dishwasher base, 1/2" less than
installation height.

STEP 3 REMOVE TOEKICK

• Remove the 4 toekick screws. Lift off the 2 piece toekick.

STEP 4 INSTALL POWER CORD

Skip this step if dishwasher will be direct wired.

Use Power Cord Kit WX09X70910, available for purchase
from an authorized GE Appliance Dealer. The power cord and
connections must comply with the National Electrical Code,
Section 422 and/or local codes and ordinances.
• Maximum power cord length is 6'.

• Connect incoming power cord white (or ribbed) to dishwasher

white, black (or smooth) to black and ground to dishwasher
green wire. Use UL listed wire nuts of appropriate size.

• Replace junction box cover. Be sure wires are not pinched

under the cover.

Figure N

Figure O

STEP 5 INSTALL 90° ELBOW

• Wrap 90° elbow with thread seal tape.
• Install a 90° elbow onto the water valve.

• Do not over tighten 90° elbow, water valve bracket could

bend or water valve ﬁ tting could break.

• Position the end of the elbow to face the rear of the

dishwasher.

Adjust to

Installation

Height

Remove

4 Toekick

Screws

Figure M

8

«
...
6
7
8
9
10
...
»

Содержание ZBD1870NSS















Отзывы:

Нет отзывов