GE ZBD1870NSS Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 14

GE ZBD1870NSS Скачать руководство пользователя страница 11

8

Turn Legs

to Adjust

Installation Instructions

STEP 10 LEVEL DISHWASHER

IMPORTANT

– Dishwasher must be level for proper

dish rack operation and wash performance.
• Make sure 1/2" minimum gap is maintained (see Figure T).
• Place level on door to check that the dishwasher is level side-

to-side. Place level on rack track inside tub to check that the
dishwasher is level front-to-back.

��

��

��

��

��

��

��

��

��

��

��

• If the dishwasher is not level, adjust the four leveling legs

individually.

Tip: Pull lower rack out, about halfway. Check to be sure the

rack does not roll forward or back into dishwasher. If the rack
rolls in either direction, the dishwasher must be leveled again.

• If door hits the tub, the dishwasher is not installed correctly.

Adjust leveling legs to align door to tub.

IMPORTANT

– After leveling, verify that the

dishwasher is still in the correct position shown in
Step 9.

Figure X

Figure Y

STEP 11 SECURE DISHWASHER TO

COUNTERTOP OR CABINET

In this step you will need

the 2 Phillips special head

screws set aside prior to

Step 1.

The dishwasher

must be secured to the
countertop or the cabinet
sides. When countertops
are made of wood,
use Method 1. When
countertops are granite or
other materials that will not
accept screws, use Method
2 to secure dishwasher at the sides.

IMPORTANT

–

Drive screws straight
and flush. Protruding
screw heads will
scratch the top or
sides of the control
panel and can interfere
with door closing.

Method 1

Secure dishwasher to wood countertop

• Fasten the dishwasher to the underside of the countertop

with the 2 Phillips special head screws provided.

Method 2

Secure dishwasher with side-mounting brackets

• Remove plug buttons (one on each side).
• Install screws through the dishwasher side mount bracket

and into the adjacent cabinet on each side. Reinstall plug
buttons.

Figure BB

��

��

��

Figure CC

��

��

��

��

��

Figure DD

Figure Z

When step is complete, close dishwasher door and verify that
gap between countertop and top of dishwasher door is at
least 1/2".

Either Method

Figure AA

2514C

Screws

Plug Buttons

Granite Countertop

Countertop

Mounting

brackets

Side-Mounting

Bracket

11

«
...
9
10
11
12
13
...
»

Содержание ZBD1870NSS















Отзывы:

Нет отзывов