GE ZBD1870NSS Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 14

GE ZBD1870NSS Скачать руководство пользователя страница 10

Countertop

Figure S

Control

Panel

Countertop

Figure T

Dishwasher

Door

1/2”

Min.

Installation Instructions

STEP 9 POSITION DISHWASHER UNDER

COUNTERTOP

• Push the dishwasher into the cabinet.
• Push the sides with your hands. Do not use your knee against

the door since door damage will occur.

• Check that the tub insulation blanket does not get

“bunched-up” or interfere with the springs as you slide it
into the cabinet.

• Center the dishwasher in the opening.
• Front of door panel should be ﬂ ush with face of cabinet.
• Carefully open and close the door to ensure that the door

panel does not catch or rub on the cabinet frame.

• If the door catches or rubs on the frame, reposition and/or

level the unit (see Step 10) until the door moves freely and
does not contact the cabinet frame.

The controls on these models are designed to be hidden by
your countertop. Align the dishwasher as shown in Figure
T. Leave a 1/2" minimum gap between the underside of the
countertop and the top of the dishwasher door as shown in
Figure W.

Note:

If the drain hose gets trapped behind the unit it can

prevent the controls from being hidden by the countertop.

Note:

If this dishwasher is replacing an existing dishwasher, the

old countertop bracket screw holes may not be in the correct
position to accept a top-control model. New holes may be
required.

Tip:

The leveling legs can be used to increase or decrease

the amount of gap between the controls and the countertop
affecting the visibility of the controls.

IMPORTANT

– Leave a 1/2" minimum gap between

the controls and the underside of the countertop to prevent

condensation and damage to the control panel from

screwheads.

Figure S

Figure T

Figure U

Figure V

Figure W

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

��

10

ON

OFF

DELAY

START

LOW RINSE AID

1 - 24 HRS.

Top View

Controls Hidden

by Countertop

«
...
8
9
10
11
12
...
»

Содержание ZBD1870NSS















Отзывы:

Нет отзывов