GE SX TRANSISTOR CONTROL IC3645SP4U400N3 Скачать руководство пользователя страница 5

Страница: 5 / 74

BASIC OPERATION AND FEATURES

SX TRANSISTOR CONTROL

Page 5

January 2000

following description provides a brief introduction to

examples of some of these features.

Section 1. 2 Solid-State Reversing

The direction of armature rotation on a shunt motor is

determined by the direction in which current flows through

the field windings. Because of the of the shunt motor field

only typically requires about 10% of the armature current at

full torque, it is normally cost effective to replace the

double-pole, double-throw reversing contactor with a low

power transistor H-Bridge circuit (Figure 4).

By energizing the transistors in pairs, current can be made

to flow in either direction in the field. The armature control

circuit typically operates at 12KHZ to 15KHZ, a frequency

range normally above human hearing. This high frequency

coupled with the elimination of directional contactors,

provides very quiet vehicle operation. The field control

circuits typically operate at 2 KHZ.

The line contactor is normally the only contactor required

for the shunt motor traction circuit. This contactor is used

for both pre-charge of the line capacitors and for

emergency shut down of the motor circuit, in case of

problems that would cause a full motor torque condition.

The line can be energized and de-energized by the various

logic combinations of the vehicle, i.e. activate on key, seat

or start switch closure, and de-energize on time out of idle

vehicle. Again, these options add to the quiet operation of

the vehicle.

Section 1. 3 Flexible System Application

Because the shunt motor controller has the ability to

control both the armature and field circuits independently,

the system can normally be adjusted for maximum system

efficiencies at certain operating parameters. Generally

speaking, with the ability of independent field and

armature, the motor performance curve can be maximized

through proper control application.

Section 1. 4 More Features with Fewer Components

Field weakening with a series wound motor is

accomplished by placing a resistor in parallel with the field

winding of the motor. Bypassing some of the current

flowing in the field into the resistor causes the field current

to be less, or weakened. With the field weakened, the motor

speed will increase, giving the effect of “overdrive”. To

change the “overdrive speed”, it is necessary to change

the resistor value. In a separately excited motor,

independent control of the field current provides for

infinite adjustments of “overdrive” levels, between

motor base speed and maximum weak field. The

desirability of this feature is enhanced by the

elimination of the contactor and resistor required for

field weakening with a series motor.

With a separately excited motor, overhauling speed

limit, or downhill speed, will also be more constant. By

its nature, the shunt motor will try to maintain a

constant speed downhill. This characteristic can be

enhanced by increasing the field strength with the

control. Overhauling load control works in just the

opposite way of field weakening, armature rotation

slows with the increase of current in the field.

Regenerative braking (braking energy returned to the

battery) may be accomplished completely with solid-state

technology. The main advantage of regenerative braking is

increased motor life. Motor current is reduced by 50% or

more during braking while maintaining the same braking

torque as electrical braking with a diode clamp around the

armature. The lower current translates into longer brush

life and reduced motor heating. Solid state regenerative

braking also eliminates a power diode, current sensor and

contactor from the circuit.

For GE, the future is now as we make available a new

generation of electric traction motor systems for electric

vehicles having separately excited DC shunt motors and

controls. Features that were once thought to be only

available on future AC or brushless DC technology vehicles

systems are now achievable and affordable.

FUSE

LINE

CAP

ARM

POS

NEG

Figure 4

A1 +

A2 -

Содержание SX TRANSISTOR CONTROL IC3645SP4U400N3











































































Результаты поиска

Содержание SX TRANSISTOR CONTROL IC3645SP4U400N3

Отзывы:

Похожие инструкции для SX TRANSISTOR CONTROL IC3645SP4U400N3

Бренды по названию

Популярные бренды

GE SX TRANSISTOR CONTROL IC3645SP4U400N3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SX TRANSISTOR CONTROL IC3645SP4U400N3

Отзывы:

Похожие инструкции для SX TRANSISTOR CONTROL IC3645SP4U400N3

Бренды по названию

Популярные бренды