GE SX TRANSISTOR CONTROL IC3645SP4U400N3 Скачать руководство пользователя страница 1

Страница: 1 / 74

INSTALLATION AND OPERATION

SX TRANSISTOR CONTROL

Page

January 2000

SEPARATELY EXCITED (SX) TRANSISTORIZED DUAL MOTOR TRACTION CONTROL

AND SERIES PUMP CONTROL

INSTALLATION AND OPERATION MANUAL

(IC3645SR4U404N2 and IC3645SP4U400N3)

Note: The information contained herein is intended to assist OEM's, Dealers and Users of electric vehicles

in the application, installation and service of GE solid-state controllers. This manual does not purport to

cover all variations in OEM vehicle types. Nor does it provide for every possible contingency to be met

involving vehicle installation, operation or maintenance. For additional information and/or problem

resolution, please refer the matter to the OEM vehicle manufacturer through his normal field service

channels. Do not contact GE directly for this assistance.

Copyright by General Electric Company January 2000

Section 1.0

INTRODUCTION ........................................................................................................................................................4

1.1

Motor

Characteristics .............................................................................................................. 4

1.2

Solid-State

Reversing............................................................................................................... 5

1.3

Flexible System Application..................................................................................................... 5

1.4

More Features with Fewer Components ................................................................................ 5

Section 2.0

FEATURES OF SX FAMILY OF MOTOR CONTROLLERS ....................................................................................6

2.1

Performance.............................................................................................................................. 6

2.1.1 Oscillator

Card

Features .................................................................................................. 6

2.1.1.a

Standard

Operation .................................................................................................. 6

2.1.1.b

Creep

Speed............................................................................................................... 6

2.1.1.c

Controlled

Acceleration

.......................................................................................... 6

2.1.2 Current

Limit ...................................................................................................................... 6

2.1.3 Braking............................................................................................................................... 6

2.1.3.a

Plug

Braking .............................................................................................................. 6

2.1.3.b

Regenerative Braking to Zero Speed...................................................................... 6

2.1.3.c

Pedal

Position

Plug

Braking .................................................................................... 6

Table of Contents

Содержание SX TRANSISTOR CONTROL IC3645SP4U400N3











































































Результаты поиска

Содержание SX TRANSISTOR CONTROL IC3645SP4U400N3

Отзывы:

Похожие инструкции для SX TRANSISTOR CONTROL IC3645SP4U400N3

Бренды по названию

Популярные бренды

GE SX TRANSISTOR CONTROL IC3645SP4U400N3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SX TRANSISTOR CONTROL IC3645SP4U400N3

Отзывы:

Похожие инструкции для SX TRANSISTOR CONTROL IC3645SP4U400N3

Бренды по названию

Популярные бренды