manualshive.com logo in svg

GE RN328HSA, Руководство пользователя, Страница: 10 / 16

Поделиться
Скачать
GE RN328HSA Скачать руководство пользователя страница 10

10

REMOVE EXHAUST ADAPTOR

If exhausting/venting using the 3

1

⁄

4

″

x 10

″

rectangular

duct—optional for JV338, JV347, JV348 and JV367
models only:

Remove the exhaust adaptor from the inside of the
hood. Set it aside along with its mounting screws. 

3

1

⁄

4

″

x 10

″

rectangular
exhaust
adaptor
and screws

REMOVE FILTER

Remove the shipping tape holding the 

metal grease

filter

in place. Pull down on the center of the front

edge of the filter. The filter will then slip out of the
retaining tabs on the back.

REVERSE THE BAFFLE FOR
DUCTED INSTALLATIONS ONLY

(JV347, JV348 and JV367 models)

If the hood is to be recirculated, skip to the next step.
Remove the baffle from the top of the hood. Re-install
the baffle so the short side marked “VENTED” is
visible. The long side of the baffle should be inside 
the hood.

REMOVE WIRING COVER

Remove the 

wiring cover

from inside the hood. 

Set the cover and its mounting screw aside. 

Wiring
cover

REMOVE WIRING KNOCKOUT

Remove either the top or the back wiring knockout as
needed and install an approved 

strain relief clamp. 

Strain relief
clamp

2

3

4

5

6

Metal grease filter

Installation Instructions

Back knockout

Top knockout

“VENTED” is visible

Strain relief
clamp

REMOVE DUCT KNOCKOUT

If 

recirculating

, non-vented ductless (JN327 and RN328,

and optional for JV347, JV348 and JV367 models only),

skip to Step 10 D and proceed

. 

Using a flat blade screwdriver, remove the appropriate

duct knockout

from the top or back of the hood.

3

1

⁄

4

″

x 10

″

Rectangular

vertical discharge.

Remove top rectangular
duct knockout only.

7

″

Round vertical

discharge. 

Remove circular

duct knockout only.

3

1

⁄

4

″

x 10

″

Rectangular

horizontal discharge. 

Remove

rear rectangular duct knockout only.

7

Содержание RN328HSA

















Отзывы:

Нет отзывов