background image

Safety Information

2

CONTENTS

Design Guide

The Installation Space ............................. 3
Product Clearances ................................... 3
Side-by-Side Installation ........................ 3

Installation Instructions

Tools, Hardware .......................................... 4
Grounding the Product ............................ 4
Staining Wood Drawer Fronts .............. 4
Installing the Custom Frame Panel ... 4
Step 1, Remove Packaging .................... 4
Step 2, Reverse Door Swing .................. 5
Step 3, Leveling ........................................... 6
Step 4, Connect Power ............................ 6

Step 5, Slide Product into Cutout ........ 6
Step 6, Install Nameplate ....................... 6
Step 7, Set Temperature Controls ...... 6
Custom Frame Panel Models ............... 6
ZTBSS1 Monogram
Tubular Handle Kit ..................................... 7
Template for Nameplate .. Back Cover

BEFORE YOU BEGIN:

Read these instructions completely and carefully.

IMPORTANT

 –

 

Save these instructions

for local inspector’s use.

IMPORTANT

 

 

Observe all governing codes

and ordinances.

Note to Installer

 

– Be sure to leave these

instructions with the Consumer.

Note to Consumer

 

– Keep these instructions with

your Owner’s Manual for future reference.

WARNING 

 

This appliance must be properly

grounded. See page 4.

AVERTISSEMENT 

Cet appareil doit être correctement mis à la terre.
Consultez page 4.

If you received a damaged wine chiller, wine reserve
or beverage center, you should immediately contact your
dealer or builder.

Skill Level

 –

 

Installation requires basic mechanical

skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.

WARNINGS:

• Use this appliance only for its intended purpose.
• Immediately repair or replace electrical service cords

that become frayed or damaged.

• Unplug the unit before cleaning or making repairs.
• Repairs should be made by a qualified service

technician.

AVERTISSEMENT :

• Il ne faut utiliser cet appareil que pour l’usage pour

lequel il a été construit.

• Il faut réparer ou remplacer immédiatement tout

cordon d’alimentation électrique effiloché ou
endommagé.

• Débrancher le bar ou le réfrigérateur a vin avant

le nettoyage ou toute intervention.

• Les réparations doivent être faites par un technicien

qualifié.

For Monogram local service in your area, call
1.800.444.1845
For Monogram service in Canada, call
1.800.561.3344
For Monogram Parts and Accessories, call
1.800.626.2002.

www.monogram.com

Содержание r10279v









Отзывы: