manualshive.com logo in svg

GE Protimeter MMS, Инструкция по эксплуатации

Поделиться
Скачать
GE Protimeter MMS Скачать руководство пользователя страница 23

Page 20

Protimeter MMS Moisture Measurement System

A1.2.2 Sub-Surface ERH Test Procedure

(using Protimeter Humidity Sleeves)

Protimeter 

Humidity Sleeves

 are convenient optional accessories for use with 

Protimeter 

Hygrosticks

. Clearance holes are drilled at the required POMs and 

the Humidity Sleeves are inserted. As each Humidity Sleeve has its own 
sealing cap, it is not necessary to plug or cover the drilled holes. Having 
placed the Humidity Sleeves in the floor slab (ideally, 24 hours before ERH 
measurements are to be taken), remove the cap and follow the procedure 
starting with step 2 in the previous section. Please refer to local standards such 
as ASTM F2170 (USA) for specific requirements.

A1.2.3 Sub-Surface ERH Test Procedure

(using Protimeter Surface Humidity Box)

If it is impractical or undesirable to take sub-surface ERH readings (the best 
technique for determining the actual moisture condition of the slab) the 

Hygrostick

 can be used in combination with a 

Humidity Box

 placed on the 

surface. Typically, 

Humidity Boxes

 are used on floors with embedded heating 

pipes or when a contractor is working to standards, such as BS 8203:1996 
(UK), that specify surface ERH techniques.

A Protimeter 

Humidity Box

 (Part No. 

BLD4711

) is available as an optional 

accessory. It should be used in accordance with applicable standard 
recommendations, or it should be placed at the POM for at least 24-hours 
prior to taking ERH readings.

The information contained in this manual is given in good faith. As the method of use of the 

instrument (and its accessories) and the interpretation of the readings are beyond the 

control of the manufacturers, they cannot accept responsibility for any loss, consequential 

or otherwise, resulting from its use.

Protimeter Hygrostick

®

 and Humistick

®

 are registered trademarks of GE

Содержание Protimeter MMS
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды