manualshive.com logo in svg

GE Protimeter MMS, Инструкция по эксплуатации

Поделиться
Скачать
GE Protimeter MMS Скачать руководство пользователя страница 17

Page 14

Protimeter MMS Moisture Measurement System

3 Diagnostic Procedure Guidelines

When diagnosing dampness in buildings, there are three key criteria that must 
be considered. These are outlined in Table 6 below.

Item 1:

The 

Search

 and 

Measure

 modes should be used in combination to 

map out the extent of a moisture problem and to distinguish between 
surface and sub-surface moisture. The profile of readings obtained 
will give insight into the potential cause (e.g. condensation, lateral 
ingress or rising dampness) of a moisture-related problem.

Far greater insight will be obtained from moisture readings taken in a 
methodical manner than from those taken in a random manner. When 
testing walls, the user should start by taking readings at the lower 
levels and move up the wall in regular steps of 4-6 in. (10-15 cm). 

Table 6: Diagnostic Criteria

Item

Criteria

Notes

1

Is a wall or other building 
element in a safe air-dry 
condition?

Air-dry is the moisture content that is 
normal and safe (from moisture-related 
deterioration or decay) in buildings. When 
the Protimeter MMS moisture meter modes 
are selected, measured values are identified 
as 

DRY

, 

AT RISK

 or 

WET

.

2

Is the surface temperature of a 
wall or other building element 
above or below the dew point?

Dew point is the temperature at which a 
given quantity of air becomes saturated 
(100% RH) and forms dew, or 
condensation. If a surface is colder than the 
dew point, condensation occurs. When the 
Protimeter MMS Condensator Mode is 
selected to measure T

DIFF

 (the proximity of 

a surface to the dew point) the instrument 
identifies either a 

NO CONDENSATION

 

condition, an 

AT RISK

 condition, or a 

CONDENSATION

 occurring condition.

3

Is a wall surface or other 
building element 
contaminated with 
hygroscopic salts or other 
conductive material?

Artificially high moisture meter readings 
may be obtained either in material that has 
been heavily contaminated by hygroscopic 
salts or in materials that are conductive by 
nature. The presence or absence of nitrates 
and chlorides should be established when 
investigating suspected rising dampness 
situations in particular.

Содержание Protimeter MMS
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды