GE Profile страница 31 Скачать руководство пользователя

Страница: 31 / 46

AT-2

LOCATING THE ANTI-TIP FLOOR

BRACKET (cont.)

Recommended Installation

– Wood

Recommended Installation

– Concrete

Minimum Acceptable #1 –

Wall Plate Stud

Minimum Acceptable #2 –

Wood Floor

Minimum Acceptable #3 –

Concrete Floor

Figure 2 – Acceptable

Screw Placement Locations

CONCRETE Wall and Floor Construction:
• Anchors required (not provided):

4 each 1/4” (6 mm) x 1-1/2” (38 mm) lag bolts

4 each 1/2” (12 mm) O.D. sleeve anchors

• Drill the recommended size holes for the

anchors into the concrete at the center of the

holes marked in Step 2.

• Install the sleeve anchors into the drilled

holes. Place the anti-tip floor bracket as

indicated in Step 2. Remove the locator

template from the floor.

• Install the lag bolts through the anti-tip floor

bracket and tighten appropriately.

WOOD Wall and TILE Floor Construction:
• For this special case, locate the 2 wall holes

identified in Fig. 2. Drill an angled 1/8” (3 mm)

pilot hole (approx. as shown in Fig. 3) in the

center of each hole.

• Mount the anti-tip floor bracket using the

Minimum Acceptable Installation #1, as

illustrated in Fig. 2.

AT-3

ANTI-TIP BRACKET INSTALLATION

WOOD Wall and Floor Construction:
• Drill the appropriate number of 1/8” (3 mm)

pilot holes in the center of each floor bracket

hole being used (a nail or awl may be used if

a drill is not available) AND remove the locator

template from the floor.

• Mount the anti-tip floor bracket by fastening

the 2, or recommended 4, #10-16 hex-head

screws tightly into place as illustrated in

Figure 3.

AT-4

POSITIONING THE REFRIGERATOR

TO ENGAGE THE ANTI-TIP FLOOR

AND BASE BRACKETS

Before pushing the refrigerator into the opening,

plug the power cord into the receptacle and

connect waterline (if equipped). Check for leaks.
Locate the refrigerator’s RH side and move back

approximately in line with the RH side of the

cabinet opening, W. This should position the

anti-tip floor bracket to engage the anti-tip base

bracket on the refrigerator.
Gently roll the refrigerator back into the cabinet

opening until it comes to a complete stop. Check to

see if the refrigerator front lines up with the cabinet

front face. If not, carefully rock the refrigerator

forward and backward until engagement occurs

and you notice that the refrigerator is fully pushed

up against the rear wall.
If Applicable: Adjust the rear (and front) wheel

height settings to fully engage the rear anti-tip

brackets, while also aligning the refrigerator

front with the cabinet front face.

NOTE:

If you pull the refrigerator out and away from the wall

for any reason, make sure the anti-tip floor bracket is

engaged when the refrigerator is pushed back against

the rear wall.

Rear RH

Corner of the

Refrigerator

Floor

Wall

Plate

Stud

Floor

Bracket

2 Screws

Must Enter

Wood or

Metal Stud

Wall

Installation Instructions

Figure 3 – Attachment to Wall and Floor

Refer to 239D1142P001, Pub No. 31-45484-5

Содержание Profile















































Результаты поиска

Содержание Profile

Отзывы:

Похожие инструкции для Profile

Бренды по названию

Популярные бренды

GE Profile, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание Profile

Отзывы:

Похожие инструкции для Profile

Бренды по названию

Популярные бренды