manualshive.com logo in svg

GE Profile PTWN8050MWW, Техническое обслуживание руководство, Страница: 26 / 46

Поделиться
Скачать
GE Profile PTWN8050MWW Скачать руководство пользователя страница 26

– 26 –

Lid Lock Assembly

The lid lock assembly is secured to the underside 
of the washer top with 2 Phillips-head screws. The 
assembly includes the interconnect cable and plug. 
It connects to a six-pin connector on the power 
board at the plug shown below.

4.  Disconnect the cable from the power board at 

the 6-pin white connector. (See

 

Circuit Board 

Connector Locator View

.

)

5.  Carefully place the shield and the control panel 

aside. 

6.  Place the top cover in the service position. (See 

Top Cover

, service position.)

7.  Remove the lid lock wire harness tie from the 

left hinge and from retainers on the bleach 
dispenser tank.

8.  Remove the 2 Phillips-head screws that attach 

the lid lock to the underside of the top cover.

Lid Lock Assembly

To remove the lid lock assembly:

1.  Place the control panel in the service position. 

(See 

Control Panel

.) 

2.  Pull out and disengage the control cover from 4 

tabs on the bottom of the control board. 

3.  Lift and remove the control cover from the 

control board. 

2

5

1

4

6

3

Pin Location

Unlocked 

Locked

Volts

Ohms

Volts

Ohms

3 to 4

5 VDC

Open

0 VDC

0 

6 to 4

0 VDC

0 

5 VDC

Open

1 to 2

12 VDC Momentarily 

Locking or Unlocking 

Door Lock Power Board WH6

WH

1

1 2

2

4

3

3

4 5

5 6

6

DOOR 

LOCK

BK BN RD

GN BL

WH

Содержание Profile PTWN8050MWW















































Отзывы:

Нет отзывов