GE Profile PTWN8050MWW Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 46

– 17 –

Washer Components

Control Panel

The control panel must be removed to access the
control system components.

To remove the control panel:

1. Remove the 2 Phillips-head screws from the

bottom of the control panel cover.

Control Board Assembly

The control board assembly

consists of the power

board and the display/logic board. Both are
attached to the control panel as one unit. Each
board is bonded to a plastic frame. The power
board has a red LED that indicates that the board
is powered and awake. (See

Circuit Board Connector

Locator View

.) The power and display/logic boards

are available separately.

To remove the control board assembly:

1. Remove the 3 Phillips-head screws from the top

of the control panel cover.

Note:

To prevent damage to the control panel and

top cover, place a protective surface over the top
cover.

2. Tilt the control panel toward the front of the

washer to disengage 5 tabs from slots located in
the top cover.

3. Lay control panel face down on the top cover

(Service position).

Tabs

WARNING:

Sharp edges may be exposed when

servicing the washer. Use caution to avoid injury.
Wear Kevlar gloves or equivalent protection.

2. Place the control panel in the service position.

(See

Control Panel

.)

3. Lift and remove the control panel cover.

4. Pull out and disengage the control cover from 4

tabs on the bottom of the control board.

5. Lift and remove the control cover from the

control board.

Service Position

(

Continued Next Page

)

Control Cover

Control Panel Cover

«
...
15
16
17
18
19
...
»

Содержание Profile PTWN8050MWW















































Отзывы:

Нет отзывов