manualshive.com logo in svg

GE Profile PTWN8050MWW, Техническое обслуживание руководство, Страница: 10 / 46

Поделиться
Скачать
GE Profile PTWN8050MWW Скачать руководство пользователя страница 10

– 10 –

Main Wash 

 

Liquid Detergent 

Compartment

Insert

Main Wash 

Powder Detergent 

Compartment

Liquid Fabric

 

Softener

 

Compartment

When using liquid detergent, make sure 
the liquid detergent compartment and 
insert are in place. For powdered 
detergent, remove both the liquid 
detergent compartment and insert. 

Powdered detergent will not dispense 
with the liquid detergent compartment 
and insert in place.

The washer control has demo mode that can be utilized to show user interface functionality. Once the user 
presses the 

START

 button, the display shall rapidly count down (at approximately 100 times faster than 

normal time), and illuminate the different cycle indicators on the 7-segment display.

To enter the demo mode:

To exit the demo mode:

With the power connected and in the idle state (all 
LCD and LED indicators off):

1.  Press and hold the

 SOIL 

and the 

SPIN

 buttons, 

then press the 

POWER

 button.

2. Press 

the 

START

 button.

1.  Unplug the washer.

2. Wait 

10-seconds.

3.  Reconnect power to the washer.

Demo Mode

Содержание Profile PTWN8050MWW















































Отзывы:

Нет отзывов