GE Profile PTW7O5, Руководство пользователя и инструкции по установке, Страница: 7 / 32

49-3000295 Rev. 0
7
U
S
IN
G
T
H
E
W
A
S
H
E
R
Getting started
Display and Status Lights
Display: The display shows the approximate time remaining until the end of the cycle. NOTE: The cycle time is affected by
how long it takes the washer to fill. This depends on the water pressure in your home. The size of the load being washed also
significantly impacts cycle time, with larger loads taking longer.
In addition, this display will, “scroll” the washer status:
• bALAnCINg Start of rebalancing cycle to redistribute clothes. Stops after rebalancing is complete.
• dELAY When Delay Wash is initiated. Replaced with estimated time when cycle starts.
• End End of current cycle.
• FILL “FILL” will scroll across the display during fill. Afterwards the estimated end of cycle time is displayed.
• H2O SUPPLY Can not sense water level (water supply possibly turned off).
• LId Cycle stopped because lid is open. Close the lid and press the Start button if needed.
• SEnSIng Sensing out-of-balance condition, waterproof items, or load size and type before and during fill (normal).
• PAUSE Cycle paused because the lid was opened during start up sequence or the Start/Pause button was pressed.
Press Start button again to restart the cycle.
Cycle status lights: Shows whether the washer is in the Pre-wash, Delay, Fill, Soak, Wash, Rinse or Spin portion of the
cycle. NOTE: Cycle status lights vary by model.
If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion of the cycle
and will stay illuminated for a short time after cycle completion. When this occurs, the washer is taking actions to correct the
out-of-balance condition and complete the cycle normally. In some cases, the washer may not be able to balance the load
and spin up to full speed. If you notice the load is more wet than normal at the end of the cycle, redistribute the load evenly
in the wash basket and run a Drain & Spin cycle.
C
Your washer is equipped with Consumer Help Indicator (CHI). CHI is our way to communicate a simple remedy for some situations
that you can perform without the need to call for service. The chart below describes the helpful messages you may notice scrolling
on your display when you return to start another load. These messages will provide simple remedies you can quickly perform.
Spin light blinking If an out-of-balance condition is detected by the washer, the Spin light will blink during the remaining portion
of the cycle and will stay illuminated for a short time after cycle completion. When this occurs, the washer
is taking actions to correct the out-of-balance condition and complete the cycle normally. In some cases,
the washer may not be able to balance the load and spin up to full speed. If you notice the load is more wet than
normal at the end of the cycle, redistribute the load evenly in the wash basket and run a
Drain & Spin cycle.
“ H2O SUPPLY ”
(Water not
entering washer)
Check your house water supply. Did you forget to turn on one or both supply valves after installation or
coming back from vacation? As soon as the message starts to scroll, the washer will initiate a 4 minute lock-
out period. The washer controls won’t respond/change during this time. After the 4 minutes, you can begin
your cycle again. If you try to bypass the lock-out period by unplugging the washer, the 4 minute timer will
start over again.
“ CAnCELEd ” “CAnCELEd” may scroll on the display if the machine was paused for longer than 24 hours or if the machine
has stopped itself before the cycle completed due to certain errors. As soon as the message starts to scroll,
the washer will initiate a 4 minute lock-out period. The washer controls won’t respond/change during this time.
After the 4 minute period, you can begin your cycle again. If you try to bypass the lock-out period by unplugging
the washer, the 4 minute timer will start over again. If the problem persists, call GE Appliances at 800.
GE.CARES (800.432.2737) for service.
“ Lid ” “Lid” will be shown on display if 3 cycles have been started without opening the lid. The washer will not
start another cycle until the lid is opened. Try opening, then closing the lid and starting a new cycle. If the
problem persists, call GE Appliances at 800.GE.CARES (800.432.2737) for service.
Consumer Help Indicator
Feature status lights indicate (see sections F and G for more details):
Pause - Will display when washer is paused between cycles.
Controls - The washer is locked - will blink once if you press any button or turn the cycle knob.
Lid Lock - The lid is locked. See the Control Lock description.
WiFi (on some models) - Will display when washer is connected via WiFi. Will blink when you are attempting to connect
your device to your home WiFi.
Spin Stop - Indicates wash basket is coasting to a stop following spin. Lid will not unlock until basket has fully come to a stop.