background image

– 13 –

Boost is the highest power level, designed
for large quantity rapid cooking and
boiling. Boost will operate for a maximum 
of 10 minutes. After 10 minutes, it will
automatically revert to power level 9.

Boost may be repeated after the initial 
10 minute cycle. 

CAUTION: 

Do not leave a pot unattended

while in the Boost Mode.

To start the Boost power setting: 

Place a pan matching the size of the
induction element over the selected
indicator ring. 

Touch the 

ON/OFF

pad. “5” will flash 

in the display.

Touch and hold the 

(+)

pad until the

display reads “H.”

NOTE: 

If the pan is removed, the display

will flash “F” alternating to “H”. After 30
seconds, the elements will turn off
automatically.

Sounds you may hear: 

You may hear a slight “buzz” sound when
cooking with the Boost or high mode. This
is normal. The sound depends on the type
of pot being used. Some pots will “buzz”
louder depending on the material. A “buzz”
sound may be heard if the pan contents
are cold. As the pan heats, the sound will
decrease. If the power level is reduced, the
sound level will go down. 

Boost Setting

11

Power Sharing

Four burner cooktops

are divided into two separate

heating zones. The right and left side cooking zones 
are powered by separate and independent induction
generators. One generator controls 2 elements, or two
cooking zones within a heating section share the power
of one generator.

Five burner cooktops

are divided into 3 zones. The

right and left side have separate cooking zones and the
large center element is another separate cooking zone.

Power Sharing is activated when both elements in the
same cooking zone are activated and one element is
set for Boost (H). The element that is not set for Boost
will change to a lower power level. This is called 
Power Sharing. When Boost operation is complete 
(10 minutes), the other element may be reset to any
power level. Both elements can operate simultaneously
at normal power level settings of “L” to 9.

4 burner cooktops with right and left side (2) induction generators. 

5 burner cooktops with right, left and center (3) induction generators.

“H” indicates that the Boost power
level has been selected for rapid
cooking and boiling.

IMPORTANT NOTE FOR FOUR BURNER MODELS: 

The elements on the right side share one generator. 
Both elements can operate at any non-Boost (level L
to 9) power level at the same time. If the large front
element is set for "H" or Boost, the smaller element 
at the right rear will be deactivated or turned off
automatically. The smaller right rear element can be
activated and set for any power level after the Boost
operation of the larger element is completed (10
minutes). 

(

Continued next page

)

Содержание Profile PHP900




































Отзывы: