GE Profile PDW8200 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 35

– 28 –

Service Mode

FLAT PANEL

BOWED PANEL

TRITON MONARCH SERVICE MODE TEST MATRIX *

KEYPAD

CONTRO

DESCRIPTION

TIME in seconds**

PAD

TYPE

Keypads to the left of the Start/Reset keypad (Selections)

FLA

Activates Drain Pump

1L

BOWE

Activates Detergent Module

75

FLA

Activates Detergent Module

2L

BOWE

Activates Main Pump

60

FLA

Activates Main Pump

3L

BOWE

Activates Heating Element

75

FLA

Activates Heating Element

4L

BOWE

Activates Drain Pump

300

FLA

Activates Water Valve

5L

BOWED

(Length of time is model dependent)

50 or 71

START/RESET

Used to EXIT Service Mode

Keypads to the right of the Start/Reset keypad (Enhancement/Extras)

Activates the following in order:

Status LEDs; Wash LEDs;

1R

FLAT

Start/Reset and Option LEDs;

3 seconds each cycle

BOWED

finally “888” will be shown

on the 3 digit display

(some models)

FLAT

2R

BOWED

Closes Active Vent

FLAT

3R

BOWED

Opens Active Vent

FLASHING DISPLAY LIGHTS

Status Indicator Lights

What It Means

START/RESET

Cycle has been interrupted by pressing the

START/RESET keypad. Light will quit

flashing after the dishwasher automatically drains out the water.

CLEAN

Unit has no water. Check the water supply. If water is turned on call for service.

5L

3L 2L 1L

4L

START
RESET

1R 2R 3R 4R

Indicates Keypad Used Only on Some Models

4L

START
RESET

1L

2L

3L

5L

1R 2R 3R

4R

Indicates Keypad Used Only on Some Models

L

T

D

T

T

D

T

D

T

D

THIS DISHWASHER IS PROGRAMMED WITH A SERVICE MODE TO AID THE TECHNICIAN IN TROUBLESHOOTING THE DISH-
WASHER. EACH COMPONENT MAY BE CYCLED TO DETECT IF IT IS FUNCTIONING CORRECTLY. COMPONENTS ARE CYCLED BY
PRESSING KEYPADS TO THE RIGHT OR LEFT OF THE START/RESET KEYPAD. DETERMINE WHICH TYPE OF CONTROL PANEL IS
PRESENT (FLAT OR BOWED) AND THEN USE THE MATRIX BELOW TO DETERMINE HOW CYCLE EACH COMPONENT.

*NOTE : Service mode may
be used for 30 minutes
maximum. After 30 minutes
the service mode will
automatically turn off.

**NOTE : Component will be
activated for indicated
time. Component may be
deactivated by pressing
the same keypad that was
pressed to activate the
component.

TO ENTER SERVICE MODE:
PRESS THE COOKWARE (POTS & PANS ON SOME
MODELS) AND THE HEATED DRY KEYPAD
SIMUTANEOUSLY FOR 3 SECONDS.

TO EXIT SERVICE MODE :
PRESS THE START/RESTART KEYPAD AT ANYTIME
TO EXIT.

«
...
28
29
30
31
32
...
»

Содержание Profile PDW8200 Series




































Отзывы:

Нет отзывов