GE Profile PDW8200 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 35

– 12 –

Dishwasher Components

Door Components

•

Interlock Switch Assembly

•

Control Module Assembly

•

Flapper (Active Vent)

•

Detergent/Rinse Module

•

Harness

Door Panel

To Remove the Door Panel:

1. Open the dishwasher door to the fully open

position.

2. Remove 10 screws (5 screws per side) which

hold the outer panel to the door assembly. Be
careful not to remove the 4 screws (2 per side)
holding the escutcheon to the door assembly.

3. Slowly close the door.

4. Once the door is closed, remove the 2 screws

that connect the bottom of the outer door panel
to the hinge arms.

5. Carefully separate the outer door panel from

the inner door panel.

To access the active vent, flapper, and door
interlock switch, the escutcheon keypad assembly
must be removed (See Escutcheon Keypad
Assembly).

To Install the Door Panel:

1. Open the dishwasher door a few inches.

2. Lift the outer door panel up in the vertical

position and hang the outer panel over top of
the escutcheon.

3. Close the door and install the 2 screws that

connect the bottom of the outer door panel to
the hinge arms.

4. Open the dishwasher door to the fully open

position and hold the top of the outer door
panel in place.

5. Install the 10 screws (5 screws per side)

which hold the outer panel to the door
assembly.

Shown with escutcheon keypad assembly and door
panel removed.

Do not remove
these screws
from either
side.

Door Screws

Door Screws

Flapper
(Active Vent)

Detergent
Module

Interlock Switch
Assembly

Harness

Control Module
Assembly

«
...
12
13
14
15
16
...
»

Содержание Profile PDW8200 Series




































Отзывы:

Нет отзывов