GE Profile PDW8200 Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 35

– 21 –

Wash Arm Assemblies

1. Check holes in spray arm for bits of china,

seeds, and other foreign matter.

2. Check spray arms for rotation.

To Disassemble Midddle Spray Arm:

1. Pull upper rack all the way out.

2. Remove nut on bottom of middle spray arm.

This will allow the middle spray arm and
bearing to be removed.

3. To remove conduit, remove screw (some

models) from hub. Press tab on side of mid
bracket to release the hub and mid conduit.

4. To reinstall arm, reverse process.

Note: Install middle spray arm with spray jets
facing the upper rack. Place bearing between nut
and bottom of mid arm.

To Remove Lower Spray Arm and Fine Filter
Assembly:

1. Remove lower rack from dishwasher.

2. Gently lift and rotate lower spray arm counter-

clockwise to remove.

3. Rotate nut hub counterclockwise to remove.

Gently lift fine filter assembly up. Remove fine
filter drain from sump.

4. Clean fine filter screen if soil is present.

5. To reinstall fine filter and lower spray arm,

reverse procedure.

Note: When installing fine filter, make sure the
drain port of the filter is engaged with the drain for
the fine filter.

Conduit Carrier

Hub

Middle

Spray

Arm

Mid

Bracket

Nut

Bearing

Upper Rack

Tab

Mid Conduit

Screw

(Optional)

Float Dome

Coarse Filter Hub

Tab

Cover Inlet

Fine Filter

Assembly

Main Conduit

Main Conduit

Mounting Screw

Lower

Fine Filter
Drain Port

Drain For

Fine Filter

Nut Hub

Spray Arm

Main Conduit

«
...
21
22
23
24
25
...
»

Содержание Profile PDW8200 Series




































Отзывы:

Нет отзывов