manualshive.com logo in svg

GE Profile Advantium SCA2000BAA, Руководство по обслуживанию

Поделиться
Скачать
GE Profile Advantium SCA2000BAA Скачать руководство пользователя страница 14

– 12 –

ATTACH THE MOUNTING PLATE 

TO THE WALL 

(continued)

7

To prepare the rear wall cutout opening
and exhaust adaptor/mounting plate for
outside back exhaust:
1. Place the mounting plate against the rear

wall as described in Step 7, item 3.

2. Using a pencil, put dots through slots F

and G, and through holes H and I. Remove
the mounting plate and draw lines
extending through the points. This will
give the location and size of the box cutout
for the rear wall duct.

• Attach the exhaust adapter to the rear

mounting plate by sliding it into the guides at
the top center of the plate on the wall side.

Push in securely until it is past the top locking
tabs and in the lower locking tabs. Take care to
assure the damper hinge is installed so that it is
at the top and that the damper swings freely.

• Carefully guide the exhaust adaptor, now

attached to the mounting plate, into the
house duct, before using the screws to attach
the plate to the wall. This will assure proper
alignment for installation.

• Return to step 7, item 5 (page 9) to continue.

After completing the installation of the
mounting plate, again check the rear 
damper for free movement to assure it 
will operate properly.

F

I

H

G

MOUNT THE OVEN

FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO
PEOPLE INSTALL THIS OVEN. 

IMPOR TANT: Do not grip or use handle during
installation.

1. Locate the grease filters packed separately

and set aside. Thread the power cord through
the hole in the bottom of the top cabinet. Keep
the cord tight throughout Step 2.

2. Install the oven by hooking the slots at the

back bottom edge onto the two lower tabs of
the mounting plate. Rotate the front of the
oven up against the cabinet bottom and using
a self-aligning screw (hardware item 3) insert
it through the top center cabinet hole and
temporarily secure the oven by turning the
screw two full turns. (It will be completely
tightened later.) Be sure to keep power
cord tight. 

NOTE: If your cabinet is metal, use the
nylon grommet around the power cord
hole to prevent cutting of the cord.

8

Slide exhaust
adaptor into
guides on 
rear panel.

Exhaust Adaptor

Damper 
(hinge side up)

Locking 
Tabs

Guides

Mounting Plate
(wall side)

Содержание Profile Advantium SCA2000BAA































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды