GE Profile Advantium SCA2000BAA Скачать руководство пользователя страница 11

Страница: 11 / 62

– 9 –

5. • Guide the wires into the duct as you place

the blower unit back into the opening.

• Secure the blower unit to the oven with the

screw from Step 2.

CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are
not pinched.

6. Replace the blower plate in the same position

as before, under its retaining flange, and
attach it with the screws.

7. Proceed to the PREPARATION OF THE

TOP CABINET section.

C. RECIRCULATION

(Non-Vented, Ductless)

NOTE: The exhaust adaptor with damper is not
needed for recirculating models. You may want
to save them for possible future use. (You must
use the Charcoal Filter Kit. See your Owner's
Manual for kit number.)

1. Remove and save the screws that hold the

blower plate to the oven.

2. • Slide the blower plate back from under its

retaining flange and lift it off.

• Remove and save the screw that holds the

blower motor to the oven.

3. Carefully pull out the blower unit. The wires

will extend far enough to allow you to adjust
the blower unit.
• Roll the blower unit so that the fan

blades are facing towards the front
of the oven.

• The wires should be routed in the grooves of

the motor frame.

Blower Plate

BEFORE:

Fan Blade Openings Facing Up

Blower
Unit

AFTER:

Fan Blade Openings Facing Front of Oven

Blower
Unit

Grooves

Retaining
Flange

Содержание Profile Advantium SCA2000BAA































































Результаты поиска

Содержание Profile Advantium SCA2000BAA

Отзывы:

Бренды по названию

Популярные бренды

GE Profile Advantium SCA2000BAA, Руководство по обслуживанию

Результаты поиска

Содержание Profile Advantium SCA2000BAA

Отзывы:

Бренды по названию

Популярные бренды