manualshive.com logo in svg

GE Profile Advantium SCA2000BAA, Руководство по обслуживанию

Поделиться
Скачать
GE Profile Advantium SCA2000BAA Скачать руководство пользователя страница 13

– 11 –

4. While holding the mounting plate with one

hand, draw circles on the wall at holes A, B, 
C and D. Four holes must be used for
mounting. If the holes are not used, the
installation will not be secure. Installer
must use these holes for proper
installation. Use toggle bolts through these
holes unless one of them lines up with a stud.
Use a wood screw for studs.

NOTE: Draw a fifth circle inside area E, through 
one of the bottom holes to match the location 
of a stud.

Set the mounting plate aside.

5.

Drill holes on the circles. If there is a stud, drill
a 3/16

″ 

hole for wood screws. If there is no

stud, drill a 5/8

″ 

hole for toggle bolts. Make

sure to use at least 1 wood screw in a
stud, and 4 toggle bolts in the dr ywall or
the plaster.

6. Attach the plate to the wall. To use toggle

bolts: Remove the toggle wings from the
bolts. Insert the bolts into the mounting plate
and replace the toggle wings to 3/4

″

past the

bolt ends. Insert the toggle wings into the
holes in the wall to mount the bracket. You
may pull forward on the bracket to help in
tightening the toggle bolts. Tighten all bolts.

For outside back exhaust: The oven requires
a rear wall cutout opening for the rear wall duct
and the exhaust adaptor must be attached to 
the mounting plate. See the next page on how to
prepare the rear wall cutout opening and the
exhaust adaptor/mounting plate for outside 
back exhaust.

3. Draw a vertical line on the wall at the center

of the 30

″

wide space.

Use the mounting plate as the template for
the rear wall. Place the mounting plate on the
wall, making sure that the tabs are against the
bottom of the cabinet. Line up the notch and
center line on the mounting plate to the
center line on the wall.

Center Line

A

C

D

B

3/16

″

Hole on Studs

5/8

″

Hole on Drywall Only

Tab

Draw 

Center Line

Draw Lines 
on Studs

Wall

Mounting

Plate

Space More Than Wall Thickness

Bolt
End

Toggle Bolt

Toggle Wings

For Outside

Back Exhaust

Only

Minimum 66

″

From the Floor

Tab

E

Mounting

Plate

Содержание Profile Advantium SCA2000BAA































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды