GE PACSystems RX3i IC695ETM001-JW Скачать руководство пользователя страница 5

Страница: 5 / 16

RX3i Ethernet Interface Module IC695ETM001-HW IPI

August 2017

GFK-2332Y

Module Installation

The ETM001 must be installed in the main (CPU) rack of an RX3i system, using a Universal Backplane such as

IC695CHS007, CHS012 or CHS016. The ETM001 supports insertion/removal while power is applied to the system (hot

swap). This module is compatible with all RX3i CPU models.

RX3i rack power may be off or on (“hot insertion”).

Holding the module firmly, align the module with the correct slot and connector, then swing the module

down until the module’s connector engages the backplane’s backplane connector. Visually inspect the

module to be sure it is properly seated.

Insert the two provided M3x5mm machine screws through the module’s bottom bracket into threaded

holes in the bottom of the backplate and screw them several turns using a #1 Phillips screwdriver. Tighten

to 0.7 N-m (6 in-lbs).

Содержание PACSystems RX3i IC695ETM001-JW

















Результаты поиска

Содержание PACSystems RX3i IC695ETM001-JW

Отзывы:

Похожие инструкции для PACSystems RX3i IC695ETM001-JW

Бренды по названию

Популярные бренды

GE PACSystems RX3i IC695ETM001-JW, Руководство пользователя

Результаты поиска

Содержание PACSystems RX3i IC695ETM001-JW

Отзывы:

Похожие инструкции для PACSystems RX3i IC695ETM001-JW

Бренды по названию

Популярные бренды