background image

Page 9 

 

USING THE QUICK ARM  (Optional, see page 1) 
The Quick Arm feature may be used if it is enabled. Quick Arm will allow the 

user to arm the security system in the AWAY mode by pressing the [EXIT

key,  or  arm  in  the  STAY  mode  by  pressing  the  [STAY] key.  This feature is 

used for ARMING ONLY, and will not disarm the security system.  This is ideal 

for a maid or baby sitter code, etc. 

 

 
CHANGING MODES WHILE SYSTEM IS ARMED 

 

Pressing the [STAY] key will turn on/off (toggle) a delay on entry/exit 

doors and turn on/off (toggle) the instant light

 

(Optional)  Press the [BYPASS] key at this time to turn on/off (toggle) all 

designated interior zones.  

 

(Optional)  When armed, pressing the [EXIT] key will start the exit delay, 

enabling you to leave the building.  

 

IMPORTANT ! 

The instant light needs to be off at this time if you plan on re-entering 

the building; otherwise you will create an alarm. You may restore an 

entry delay by pressing the [STAY] key again. 

 

 

DISARMING THE SYSTEM 
When you enter the protected area through one of the designated Entry/Exit 

doors, the keypad control will sound a continuous tone for the duration of the 

entry delay time, or until you enter a valid code.  The red armed light will go 

off and the tone will stop. The security system is now DISARMED.  If a valid 

code is not entered before the end of the entry delay, an alarm will occur.  

(NOTE:  If the red armed light is flashing during the entry delay, the 

alarm system has been activated in your absence. Leave the building 

immediately and call your alarm company and/or the police from a 

safe location.) 

 

 
CANCEL / ABORT FEATURE  (Optional, see page 1) 
The  cancel light will flash during an abort delay time.  If a code is entered 

followed by the [CANCEL] key while this light is flashing, all abortable reports 

will stop the communication process. Entering a code followed by the 

[CANCEL] key during or after an alarm report to the central station will cause 

the  cancel light to come on. It will stay on until the central station has 

received the cancel report. 

Содержание NX-1300E

























Отзывы: