manualshive.com logo in svg

GE MultiLink ML1200, Инструкция по эксплуатации

Поделиться
Скачать
GE MultiLink ML1200 Скачать руководство пользователя страница 80

5–8

MULTILINK ML1200 MANAGED FIELD SWITCH – INSTRUCTION MANUAL

IP ADDRESSING

CHAPTER 5: IP ADDRESSING

5.3

Setting Parameters

5.3.1

Setting Serial Port Parameters

To be compliant with IT or other policies the console parameters can be changed from the 
CLI interface. This is best done by setting the IP address and then telnet over to the switch. 
Once connected using telnet, the serial parameters can be changed. If you are using the 
serial port, remember to set the VT-100 emulation software properties to match the new 
settings.

The serial port parameters are modified using the 

set serial

 command with the 

following syntax:

set serial [baud=<rate>] [data=<5|6|7|8>] [parity=<none|odd|even>] 

[stop=<1|1.5|2>] [flowctrl=<none|xonxoff>]

Where 

<rate>

 = standard supported baud rates.

Note

Changing these parameters through the serial port will cause loss of connectivity. The 
terminal software parameters (e.g. HyperTerminal) will also have to be changed to match 
the new settings.

To see the current settings of the serial port, use the 

show serial

 command to query the 

serial port settings as illustrated below.

ML1200#

 

show serial

Baud Rate: 38400

Data: 8

Parity: No Parity

Stop: 1

Flow Control: None

5.3.2

System Parameters

The system parameters can be queried and changed. To query the system parameters, 
two commands are frequently used: 

show sysconfig

 and 

show setup

. Usage for both 

commands is illustrated below.

The following example lists system parameters using the 

show setup

 command. Most 

parameters here cannot be changed.

ML1200#

 

show setup

Version: ML1200 build 3.3.0 March 19 2009 14:22:43

MAC Address: 00:20:06:27:0a:e0

IP Address: 3.94.247.41

Subnet Mask: 255.255.252.0

Gateway Address: 3.94.244.1

CLI Mode: Manager

System Name: ML1200

System Description: 12 Port Modular Ethernet Switch

System Contact: [email protected]

System Location: Markham, Ontario

System ObjectId: 1.3.6.1.4.1.13248.12.7

ML1200#

The following example lists system parameters using the 

show sysconfig

 command. 

Most parameters here can be changed.

Содержание MultiLink ML1200

























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды