manualshive.com logo in svg

GE Monogram ZV950, Руководство по установке, Страница: 9 / 12

Поделиться
Скачать
GE Monogram ZV950 Скачать руководство пользователя страница 9

9

 1  INSTALL FRAMING 

             

FOR HOOD SUPPORT

IMPORTANT: Framing must be capable  

of supporting 100 lbs.

Installation Instructions

If drywall is present, mark the screw hole locations for 
the top mounting brackets. Remove the template.
• Cutaway enough drywall to expose 2 vertical studs at 

the bracket location indicated on the template.

• Install a horizontal support at least 1" x 6" between two 

wall studs at the top bracket installation location

. The 

horizontal support must be flush with the room side of 
the studs.

 Use cleats behind both sides of the support  

to secure the support to wall studs. 

• Reinstall drywall.

Centerline of 

Installation

Space

8" Min. Opening for Ductwork

124Dia25

View From Rear

Cleats

1" x 6" Min.

Mounting

Support

 2  INSTALL MOUNTING BRACKETS

This vent hood must be secured to the horizontal support or wall 
studs.

• With the template taped in place, use a punch  

to mark all mounting screw locations.

• Drill 1/8" pilot holes at the 6 punched locations.
• Remove the template.
• The 4 support bracket holes must enter studs  

or the horizontal support.

Note: 

Screws “A” and 

“B” are pre-assembled 

onto the brackets. Do not 

remove these screws.

124Dia15

Screws

“B”

Screws

“A”

• The two lower holes can be enlarged if they did not 

enter studs to 3/8". Tap anchors for wall fasteners  
into the bottom holes.

  – Screws should be inserted by hand into the fasteners 

to allow anchors to expand against the wall material. 
Remove the screws for final installation.

• Secure the mounting brackets to the wall studs with 

wood screws provided.

Содержание Monogram ZV950













Отзывы:

Нет отзывов