manualshive.com logo in svg

GE Monogram ZV950, Руководство по установке, Страница: 8 / 12

Поделиться
Скачать
GE Monogram ZV950 Скачать руководство пользователя страница 8

Centerline

8" Min. Above

Top Mounting

Bracket Holes

6-1/4"

Centerline To Wall

FOR WALL VENT DUCT

FOR CEILING

VENT DUCTING

CL

124Dia14

8-1/2" Dia. Hole

CL

CL

CL

124Dia11

Installation Preparation

8

DUCTWORK, WIRING LOCATIONS

Determine the exact location of the vent hood.
• Locate the template packed with the literature.
  – Measure 36" from the floor to the top of the cooking 

surface. Add 25-1/2" (or other recommended space) 
from the cooking surface to the bottom of the hood. 
Mark that location.

  – Use a level to draw a straight pencil line on the wall.
 

CHECK INSTALLATION HARDWARE

Locate the hardware accessory box packed with the 
hood and check contents.

124Dia10

124Dia8

124Dia9

124Dia5

124Dia7

124Dia13

2 Large

Flat Washers

3 Phillips Head

Decorative Screws

3 Stainless Steel Grease Filters

8 Wood 

Screws

Wall Mount Template

2 Mounting Brackets

Duct Cover Bracket

4 Wall 

Fasteners

2-piece

Decorative Duct Cover

(dimension shown

for reference only)

  – Tape the template in position along the penciled 

line. CHECK TO BE SURE THE TEMPLATE IS 
LEVEL.

Ceiling ducting:

If ductwork will vent straight up to the ceiling:
• Use a level to draw a line straight up, from the  

centerline on the template to the ceiling.

• Measure 6-1/4" from the back wall to the centerline 

of a 8-1/2" hole on the ceiling.

Note:

 If drywall is not present, add drywall thickness

to the 6-1/4" dimension.

Wall Ducting:

If ductwork will vent to the rear:
• Use the level to draw a line straight up from the  

centerline on the template. 

• Measure at least 8" above the top mounting bracket 

holes shown on the template to the centerline of an 
8-1/2" dia. duct hole. (Hole may be elongated for 
duct elbow.)

HOUSE WIRING LOCATION:

• The junction box is located on the top of the hood, 

at the back right side.

• Route house wiring as close to the ceiling location  

as possible, through the ceiling, soffit or back wall. 
Wiring should enter at least 4" above the bracket  
on the right side.

124Dia6

124Dia12

16"

23"

11"

24"

124Dia13

Содержание Monogram ZV950













Отзывы:

Нет отзывов