manualshive.com logo in svg

GE Monogram ZV800, Руководство по установке, Страница: 22 / 24

Поделиться
Скачать
GE Monogram ZV800 Скачать руководство пользователя страница 22

22

Installation Instructions

UNDER-CABINET INSTALLATION

COMPLETE THE INSTALLATION
AND CONNECT DUCTWORK

•

Drive 2 screws into each side bracket. 
Be sure the screws engage the filler blocks 
or the cabinet bottom.

• Pull the glass canopy forward to access and install 

2 screws through the hood and into the brackets on
both sides.

• Use duct tape to secure the duct to the exhaust

outlet in the top of the hood. Do not use screws 
at this location.

If there is a noticeable gap between the hood and the
bottom of the cabinet on the sides:

•

Slide canopy forward and install original top screws
through the bottom of the hood and into cabinet
bottom or frame.

NOTE:

Install wood filler blocks if necessary to

accept the screws.

7

Install 2 Screws into

Each Side Bracket

MOUNT THE HOOD 

•

Carefully, lift the hood into the cabinet. Guide the
hood upwards to meet the ductwork.

IMPORTANT:

One person must hold the hood in place

while the other drives the screws into the mounting
frame.

6

Install original top screws

Install a wood screw

on each side of the

mounting frame

Содержание Monogram ZV800

























Отзывы:

Нет отзывов