manualshive.com logo in svg

GE Monogram ZV800, Руководство по установке, Страница: 15 / 24

Поделиться
Скачать
GE Monogram ZV800 Скачать руководство пользователя страница 15

15

Installation Instructions

INSTALL MOUNTING BRACKET

This vent hood must be secured to the horizontal
support or wall studs.

•

With the template taped in place, use a punch to
mark all mounting screw locations.

•

Drill 1/8” pilot holes at the 6 punched locations.

•

Remove the template.

•

The 2 holes in the support bracket holes must enter
studs or the horizontal support.

•

Use wood screws to secure the mounting bracket to 
the wall. The screws must engage wall studs or the
installed horizontal mounting support. 

•

Check to be sure that the bracket is level. 
There is no way to level the hood after hanging 
it from this bracket.

2

WALL-MOUNTED INSTALLATION—RECIRCULATING

PREPARE THE HOOD

•

Remove the hood from the box. Remove packaging
and tape.

•

Remove one screw on each side of the cover on the
electrical panel. Lift off the cover and set aside with
screws.

•

Stand the electrical panel upright.

•

Align the screw holes in the bottom of the panel with
the holes on the base of the hood at the front side.

•

Install 3 screws provided.

•

Snap the damper into the 
exhaust outlet on the top of
the hood.

3

Remove 2 side

cover screws

Install

damper

Electrical

panel

Secure

electrical panel

with 3 screws

Junction box

Inside screw

Содержание Monogram ZV800

























Отзывы:

Нет отзывов