manualshive.com logo in svg

GE Monogram ZBD3500, Руководство по установке, Страница: 29 / 32

Поделиться
Скачать
GE Monogram ZBD3500 Скачать руководство пользователя страница 29

29

GPF53 Mounting Kit

Mounting Brackets

Tools and materials required:

• 5/16" nut driver

• Phillips screwdriver

• Safety glasses

The GPF53 mounting kit is to be used for
attaching dishwashers to adjacent cabinets
when countertops are stone or other materi-
als which will not accept screws.

Position
Mounting
Brackets

• Fold factory installed flanges back 180

°

 and

flatten against tub frame.

• Position mounting brackets over frame and

in recessed area, as shown.

Secure
Mounting
Brackets

• Measure width of cabinet opening.
• Insert two 10/32" machine screws into each

bracket. Do not tighten.

• Adjust brackets to match the cabinet open-

ing width.

• Tighten screws against metal frame.

Finalize
Installation

• If necessary preparations for plumbing and

electrical connections have been completed,
slide dishwasher into place.

• Secure each mounting bracket to adjacent

cabinets with one screw.

Fold Flanges
Back 180

°

and Flatten
Against Tub
Frame

Adjust
To Cabinet
Opening

Содержание Monogram ZBD3500

































Отзывы:

Нет отзывов