GE Monogram ZBD3500 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 32

GE Monogram ZBD3500 Скачать руководство пользователя страница 24

24

GPF425 Series Trim Kit

1/4" Custom Panels

• Place bottom trim against the bottom of the

access panel.

• Install color matched screw in the center,

then left and right screws.

• Gently, bend both ends of the bottom trim

upwards to form a “U” shape.

• Slide the 1/4" custom panel down into “U”

shaped trim.

• Place top trim over the panel. Use masking

tape to hold in place.

• Drill 3 holes into the top of the trim and

into the assembly. Install 3 color matched
screws provided.

• Drill holes through the side trim holes and

into the access panel. Secure each side of
the trim with one screw. Remove tape.

• Place the toekick against the bottom of the

dishwasher.

• Place the access panel assembly against the

dishwasher and tighten the attached screws.

• Re-install two original bottom screws loosely.

Adjust the toekick up or down and tighten
screws.

This trim kit is designed to accommodate
1/4" thick panels. A raised panel screwed or
glued to 1/4" thick backing can be used. The
raised portion of the panel must be fabricated
to permit clearances for the trim on all sides.

• “X” Clearance shown at the bottom of the

raised panel must be maintained to prevent
the door from striking the access panel when
opened.

Appearance

Total

“X”

Panel

Backing

Thickness

Clearance

3/4"

1/4"

1"

2"

1/2"

1/4"

3/4"

1-7/8"

IMPORTANT!

GPF100 Dishwasher Door Spring Kit MUST BE installed
when custom door panels weigh 4 pounds or more.

A 3/4" thick custom panel may be installed by
routing the top and sides to 1/4" thickness.
The bottom edge, Dimension “X”, should be
and 1-1/2" high and 1/4" thick.

Install Center
Screw First

Tighten 2 Screws

19-3/4"

1/4" Min. Clearance

23-9/16"

Appearance

Panel

1/4"

Thick

Panel

1/8" Min.

Clearance

1/8" Min.

Clearance

X

Clearance

3-11/16"

1/4" Min. Clearance

All Sides

23-9/16"

Access Panel

Step 4:
Install Custom
Access Panel

Step 5:
Install Access
Panel Assembly
And Toekick

Installation
Options

«
...
22
23
24
25
26
...
»

Содержание Monogram ZBD3500

































Отзывы:

Нет отзывов