GE Monogram ZBD1800K Series Скачать руководство пользователя страница 6

Страница: 6 / 46

– 6 –

Control Panel Features

Control Timer:

HEAVY WASH

NORMAL WASH

LIGHT WASH

CHINA CRYSTAL

RINSE ONLY

For rinsing partial loads that will be washed later. Do not use detergent with this cycle.

This cycle is for everyday dishes and glassware.

This cycle is specifically designed for lightly soiled china and crystal.

This cycle is for medium-soiled dishes and glassware.

This cycle is for heavily soiled dishes and glassware.

START

Close the dishwasher door and turn the control timer knob to the desired setting.
Water fill begins and approximately 30 seconds later, the wash action begins.

Door Latch
Switch:

Automatically shuts off the dishwasher whenever the dishwasher door is opened. The
dishwasher will not resume operation until the door is closed.

Door Latch Switch

Control Timer

Static Vent

Содержание Monogram ZBD1800K Series















































Результаты поиска

Содержание Monogram ZBD1800K Series

Отзывы:

Похожие инструкции для Monogram ZBD1800K Series

Бренды по названию

Популярные бренды

GE Monogram ZBD1800K Series, Техническое обслуживание руководство

Результаты поиска

Содержание Monogram ZBD1800K Series

Отзывы:

Похожие инструкции для Monogram ZBD1800K Series

Бренды по названию

Популярные бренды