GE MobileLink CB-1000 Скачать руководство пользователя страница 38

Страница: 38 / 44

MobileLink

Revision D

2002783-060

Technical Specifications

Technical Specifications

Client Bridge

Manufacturer/Model

Symbol Technologies/CB-1000

Dimensions

6.2 in. x 3.9 in. x 1.0 in.
15.7 cm x 9.9 cm x 2.5 cm

Serial Port

DB9 female with optional hardware flow control, baud rates 9600 - 115,200

Ethernet Port

10BaseT with straight-through RG-45

Antenna Connector

Reverse BNC optional for installations

Operating Temperature

-4°F to 131°F
-20°C to 55°C

Storage Temperature

-40°F to 194°F
-40°C to 90°C

PC Card

Manufacturer/Model

Symbol Technologies/LA-4121-1120-US

Frequency Range

Worldwide product covering 2.4 to 2.5 GHz, programmable for different country
regulations

Data Rate

11 Mbps per channel maximum

Max. Output Power

100 mW

Power Management

Continuous Aware and Power Saving Modes

Range

Data throughput scaled to support up to 1,500 ft./450 m outdoors and up to 300 ft./90 m
indoors

TX Maximum Radiated EIRP

FCC regulations part 15.247 in U.S.

Modulation

Direct Sequence Spread Spectrum (DSSS) with BPSK (1 Mbps), QPSK (2 Mbps), and
CCK (5.5 and 11 Mbps)

TX Out-of-Band Emissions

FCC regulations part 15.247, 15.205, 15.209 in U.S.

Operating Temperature

-4° to 158°F (-20° to 70°C)

Storage Temperature

-22° to 176°F (-30° to 80°C)

Driver Software Support

Microsoft® Windows® 95/98, Windows NT 4.0, Windows CE 2.11 and 3.0, Windows
2000, Windows ME; NDIS 4 AND 5

Access Protocol

CSMA/CA

Roaming

Virtually instantaneous

Содержание MobileLink CB-1000













































Результаты поиска

Содержание MobileLink CB-1000

Отзывы:

Бренды по названию

Популярные бренды

GE MobileLink CB-1000, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание MobileLink CB-1000

Отзывы:

Бренды по названию

Популярные бренды