GE Mini COM Express 10 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 82

background image

3

Installation and Startup

This chapter describes the installation of the mCOM10-L1500 module on a carrier board
and initial startup operations.

3.1

Required Materials

The following items are required to start the board in a standard configuration:

•

Carrier board and power supply

•

Keyboard and mouse

•

Video monitor

3.1.1

Carrier Board and Power Supply

A carrier routes the I/O signals
of the mCOM10-L1500 to the
connectors.

Refer to chapter,

Specifications

You will need a carrier board wired with either an integrated or external regulated power
supply capable of providing stable low noise primary and standby sources. Verify that the
supply meets the voltage and total power requirements of the mCOM10-L1500.

Warning

Verify that the power supply is turned OFF while
plugging or unplugging the board onto or from a
carrier card, respectively.

3.1.2

Keyboard and Mouse

The keyboard is attached to the
carrier board.

A compatible keyboard for initial system operation on the carrier board is required.
Depending on your application, this may be a standard keyboard, or one that uses
membrane switches for harsh environments.

3.1.3

Video Monitor

Any video monitor with an appropriate connection to a Digital Display Interface (DDI)
can be used initially for display output. Compatible interfaces are DisplayPort, DVI, and
HDMI. Access to the video signal is provided through the carrier board.

Installation and Startup

GFK-2896 Hardware Reference Manual 19

For public disclosure

«
...
17
18
19
20
21
...
»

Содержание Mini COM Express 10



















































































Отзывы:

Нет отзывов

Похожие инструкции для Mini COM Express 10

Бренд: Ubisys Страницы: 2

SolarCell Remote

Бренд: Samsung Страницы: 2

Бренд: JDS Uniphase Страницы: 27

Бренд: Danfoss Страницы: 20

Бренд: OEG Страницы: 168

Бренд: TA Hydronics Страницы: 14

Бренд: BADODOSECURITY Страницы: 8

Бренд: Saftronics Страницы: 13

Бренд: Samson Страницы: 6

Бренд: Yamaha Страницы: 92

Бренд: WABCO Страницы: 4

Бренд: Rayrun Страницы: 4

Бренд: Parker Страницы: 29

HydroTap G5 Touch-Free Wave

Бренд: Zip Страницы: 24

Бренд: micro-trak Страницы: 44

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Бренд: Bardiani Valvole Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды