GE LOGIQ 400 Скачать руководство пользователя | Manualshive

Страница: 200 / 526

background image

GE MEDICAL SYSTEMS

LOGIQ 400 SERVICE MANUAL



2127661

RENEWAL PARTS

6–70

REV 9

6–2–1 Monitor Assy (FRU No. 100)

Time Required

0.25 Hours

Tool Required

Screwdriver
Hexagonal Wrench

Procedure

WARNING!

PERSONAL INJURY HAZARD. THE NECK ASSY IS SPRING LOADED. RELEASING ARM
WHEN MONITOR IS NOT INSTALLED WILL CAUSE SUDDEN UPWARD MOVEMENT. KEEP
YOUR HEAD AND BODY AWAY FROM ABOVE NECK ASSY.

Refer to ILLUSTRATION 6–14.

1.

Turn OFF the system.

2.

Remove the CRT Filter. Refer to 6–2–6 on page 6–79.

3.

Unscrew four hexagonal screws ( 1 – 4 ) located beneath the horizontal part of the Neck Assy.

4.

Remove the cover located at the bottom of the Neck Assy.

5.

Unscrew two screws ( 5 and 6 ) and remove the plate fixing the cables.

6.

Disconnect the four connectors ( 7 –

10

).

7.

Remove the screw cap located at position (

11

).

8.

Loosen one screw (

11

) and pull the Monitor Assy upwards.

Note

When replacing the monitor with the new Monitor Assy (2162081), be sure to attach the proper label
included with the Monitor Assy on to the Escutcheon. To attach the new label, refer to the procedures
in section 6–2–2 on page 6–72.

Note

The color of the Escutcheon for LOGIQ



400CL is different from the other color monitor assy. Use the

proper FRU when replacing the monitor assy for the LOGIQ



400CL.

«
...
198
199
200
201
202
...
»

Содержание LOGIQ 400















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LOGIQ 400

Бренд: THORLABS Страницы: 44

Бренд: IDEAL Страницы: 12

Бренд: Jaga Страницы: 32

Бренд: Taylor Страницы: 60

Бренд: TANDBERG Страницы: 23

Бренд: Waterpik Страницы: 2

Бренд: ZacUrate Страницы: 2

Бренд: ZacUrate Страницы: 2

Бренд: Zero 88 Страницы: 12

Бренд: Zeiss Страницы: 119

Бренд: Zehnder Rittling Страницы: 32

Pendalyte 40472U

Бренд: Lightolier Страницы: 3

Бренд: Martin Страницы: 202

Бренд: Daavlin Страницы: 55

Бренд: Daavlin Страницы: 19

Бренд: ABB Страницы: 106

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Бренд: REED Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды