manualshive.com logo in svg

GE JVM1500 Series, Руководство по установке

Поделиться
Скачать
GE JVM1500 Series Скачать руководство пользователя страница 13

MOUNT THE OVEN

FOR EASIER INSTALLATION AND PERSONAL
SAFETY, WE RECOMMEND THAT

TWO PEOPLE

INSTALL THIS OVEN. 

IMPORTANT: Do not grip or use handle
during installation.

NOTE: 

If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent
cutting of the cord.

NOTE:

We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used,
case damage may occur from over tightening
screws.

A3

13

NOTE:

When mounting

the oven, thread power
cord through hole in
bottom of top cabinet.
Keep it tight throughout
Steps 1–3. Do not pinch
cord or lift oven by
pulling cord.

Installation Instructions

USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET

You need to drill holes for the top support screws, and
a hole large enough for the power cord to fit through.

•

Read the instructions on the TOP CABINET
TEMPLATE.

•

Tape it underneath the top cabinet. 

•

Drill the holes, following the instructions on the
TOP CABINET TEMPLATE.

CAUTION: 

Wear safety goggles when drilling holes 

in the cabinet bottom.

A2

Lift oven, tilt it
forward and 
hook slots at back
bottom edge onto
two lower tabs of
mounting plate.

1

Rotate front of
oven up against
cabinet bottom.

2

Содержание JVM1500 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды