MARK HOLES
Select the vent option that your installation will
require and proceed to that section:
Hood mounting screws (4)
13
15
⁄
16
″
(30
″
hood)
16
15
⁄
16
″
(36
″
hood)
13
15
⁄
16
″
(30
″
hood)
16
15
⁄
16
″
(36
″
hood)
Cabinet front
Center
line
Electrical access hole
(in cabinet bottom)
Wood shims
(recessed-
bottom cabinets only)
Vertical duct
access hole
10
1
⁄
2
″
1
1
⁄
2
″
2
″
7
1
⁄
2
″
5
″
1
1
⁄
4
″
A.Outside top exhaust
(Vertical duct—3
1
⁄
4
″
x 10
″
Rectangular)
•
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
B.Outside top exhaust (Vertical duct—7
″
Round)
•
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
Hood mounting screws (4)
13
15
⁄
16
″
(30
″
hood)
16
15
⁄
16
″
(36
″
hood)
13
15
⁄
16
″
(30
″
hood)
16
15
⁄
16
″
(36
″
hood)
Cabinet front
Center
line
Electrical access
hole
(in cabinet bottom)
Wood shims
(recessed-
bottom cabinets only)
Access
hole for 7
″
round duct
10
1
⁄
2
″
1
1
⁄
2
″
2
″
7
1
⁄
2
″
5
″
Cabinet
bottom
8
″
DIA.
HOLE
CUT HOLES
Cut holes at marked locations for duct and electrical
wiring. For the vertical duct, cut out 3/4
″
extra
toward the front of the cabinet so you can move the
duct freely when installing the hood. It may also ease
installation by cutting the hole 10
1
⁄
2
″
instead of 10
″
.
FOR RECESSED-BOTTOM
CABINETS ONLY
RUN WIRES
Run the electrical wires through the wall or
cabinet according to National Electrical Code
and applicable local codes.
NOTE:
DO NOT turn the power on until
installation is complete.
Cabinet Bottom
12
14
13
15
SCREW IN PARTWAY
Drive a mounting screw (from the hardware packet)
partway into each center of the narrow neck of the
keyhole slots marked on the cabinet bottom.
FEED IN WIRES
Lift the hood into position and feed the house
wiring through the wiring knockout.
16
17
Wood shims
(recessed-bottom cabinets only)
Cabinet front
Center line
Electrical access hole
(in wall)
Hood mounting screws (4)
Horizontal duct
access hole
Cabinet
bottom
13
15
⁄
16
″
(30
″
hood)
16
15
⁄
16
″
(36
″
hood)
3
⁄
4
″
1
⁄
8
″
3
3
⁄
4
″
5
1
⁄
4
″
5
1
⁄
4
″
7
1
⁄
2
″
13
15
⁄
16
″
(30
″
hood)
16
15
⁄
16
″
(36
″
hood)
C.Outside rear exhaust
(Horizontal duct—3
1
⁄
4
″
x 10
″
Rectangular)
•
Use the diagram or the hood as a template and
mark the locations on the cabinet for ductwork,
electrical wiring and keyhole screw slots.
D.Recirculating (non-vented ductless—
Available on JV5 Series models only)
•
Use the hood as a template and mark the locations
on the cabinet for the electrical wiring and keyhole
screw slots.
•
Since the hood is to be recirculated (not to be vented
outside), do not cut out any vent openings in the wall
or cabinet bottom.
Wood shims
•
If the cabinets have front, side or back trim, make
2 wood shims the width of the trim and attach them
to the cabinet bottom recess on both sides. See Step
12 for marking locations.
5
1
⁄
4
″
5
1
⁄
4
″
Installation Instructions
13