GE JV536 Скачать руководство пользователя страница 12

Ties

12

REMOVE DUCT KNOCKOUT(S)

If 

recirculating

, non-vented ductless (optional for 

JV5 Series models only), see note below and 

skip to 

Step 12 D and proceed

We do not recommend the

recirculated configuration for JV6 Series models.

Using a flat blade screwdriver, remove the appropriate

duct knockout(s)

from the top or back of the hood.

3

1

4

x 10

Rectangular

vertical discharge.

Remove top rectangular
duct knockout only.

7

Round vertical

discharge. 

Remove semi-

circular duct knockout and top
rectangular duct knockout.

3

1

4

x 10

Rectangular

horizontal discharge. 

Remove

rear rectangular duct knockout only.

FOR HORIZONTAL DISCHARGE
INSTALLATIONS ONLY:

Remove the 

plate

(on models so equipped) in front 

of the horizontal discharge knockout. Cut the 

ties

lift plate out and discard plate. DO NOT REMOVE 
the 

metal strip

held in place with two 

screws

.

Metal strip

Plate

FOR 3

1

4

X 10

RECTANGULAR

DUCTED DISCHARGE
INSTALLATIONS ONLY:

Attach 

exhaust adaptor/damper

over knockout

opening with two exhaust adaptor screws. Make sure
damper 

pivot

is nearest to 

top/back edge

of hood.

Remove 

tape

from damper flap.

Up to 1

side-to-

side adjustment

Tape

Top/back edge

Exhaust adaptor/damper
(vertical discharge position
shown)

Pivot

FOR 7

ROUND VERTICAL

DUCTED DISCHARGE
INSTALLATIONS ONLY:

Re-install the 

7

round exhaust adaptor

with its

screws, removed in Step 2 under the “Prepare the
Hood” section.

8

9

10

11

7

round

exhaust
adaptor

NOTE: 

The 7

round exhaust adaptor can be installed 

up to 1 inch on either side of the hood center to
accommodate off-center ductwork. In extreme off-center
installations, one end of the duct connector may need 
to be trimmed to clear the electrical cable clamp.

NOTE: 

The 7

round damper is not included with 

this product. It can be purchased as a kit by calling
800.626.2002. Order kit number JXDA23.

Installation Instructions

Screw

NOTE: 

The exhaust adaptor/damper can be installed

up to 1 inch on either side of the hood center to
accommodate off-center ductwork. In extreme off-
center installations, one end of the duct connector may
need to be trimmed to clear the electrical cable clamp.

NOTE: 

If the hood is to be installed in a 

recirculating

,

non-vented ductless manner, order charcoal filters, 
kit number WB02X10707 for 30

hood models or 

kit number WB02X10708 for 36

hood models. 

These kits can be ordered from your GE supplier. 

Skip to Step 12 D and proceed

.

Содержание JV536

















Отзывы: