GE Integritas 3TL125-SACY-D10Y-P000 Скачать руководство пользователя страница 21

Страница: 21 / 24

Document 8600092587P r04 2019 May

Integritas Wall Mount Charger

Quick Start Guide

Parts List

continued

Specifications and Application

•

External Surge Protective Device (SPD) is required on all AC inputs.

•

Equipment Safety is Approved in UL1449/IEC 60664

1 Installation Category II environments for ambient temperature up to 50°C.

Models using IP020ACR125ATEZ rectifiers:

For input voltages above 266V, the maximum output current and power are de

rated by 2.8% per °C for operating ambient above 40°C.

•

Equipment and subassembly ports:

1. are suitable for connection to intra

building or unexposed wiring or cabling;

2. can be connected to shielded intra

building cabling grounded at both ends.

•

Grounding / Bonding Network –

Connect to an Isolated Ground Plane (Isolated Bonding Network) or an Integrated Ground Plane (Mesh

Bonding Network or Common Bonding Network).

•

Installation Environment

Install where NEC applies.

Reference Documents

These documents are available at

www.gecriticalpower.com

Document

Title

8600092588P

Pulsar XL Product Manual

850049786

Pulsar Plus Controller Family Troubleshooting

601

Shiloh Rd.

Plano, TX 75074

972

244

9288

www.gecriticalpower.com

Thermal Probes

Comcode

Description

Application

1600093512A

DTP873_AMBIENT

Ambient Thermal Probe Kit

1600093513A

DTP873_BATTERY

Battery Terminal Thermal Probe Kit

Additional Accessories (Mounting Hardware, Filters, etc.)

Comcode

Description

Application

1600097831A

19IN IWC 19IN FRAME MOUNT KIT

Mounting hardware to attach 19" Battery Charger to 19" Frame

1600097832A

19IN IWC 23IN FRAME MOUNT KIT

Mounting hardware to attach 19" Battery Charger to 23" Frame

850052732

FILTER, WALL BOX, 19"

Air Filter for 19" Battery Charger cabinet

850053032

FILTER, WALL BOX, 23"

Air Filter for 23" Battery Charger cabinet

4600097827P

VAL

350

ST 2859602

AC Line Surge Arrestor Replacement Module

4600097268P

VAL

N/PE

350

ST 2859699

AC N

PE Surge Arrestor Replacement Module

4600097830P

PST

SEC

24P 2905232

24V DC Surge Arrestor Replacement Module

4600219078P

VAL

600D/30/P

2910341

Type 2

600 V AC Plug For 3

phase DELTA Surge Protection Device

4600097829P

PST

SEC

60P 2905233

48V DC Surge Arrestor Replacement Module

4600097828P

PST

SEC

230P 2905235

125V DC Surge Arrestor Replacement Module

Содержание Integritas 3TL125-SACY-D10Y-P000

























Результаты поиска

Содержание Integritas 3TL125-SACY-D10Y-P000

Отзывы:

Бренды по названию

Популярные бренды

GE Integritas 3TL125-SACY-D10Y-P000, Быстрый старт

Результаты поиска

Содержание Integritas 3TL125-SACY-D10Y-P000

Отзывы:

Бренды по названию

Популярные бренды