manualshive.com logo in svg

GE Integritas 3TL125-SACY-D10Y-P000, Быстрый старт

Поделиться
Скачать
GE Integritas 3TL125-SACY-D10Y-P000 Скачать руководство пользователя страница 15

Document 8600092587P   r04 2019 May

 

15

 

Integritas Wall Mount Charger 

-

 Quick Start Guide

 

 

 

Information: Controller Alarm Relay Jumpers

 

Jumpers are located on the side top of the controller.

 

Alarm Relay Jumper Factory Defaults are Open On Alarm.

 

1.

 

Remove Controller 

-

 2 thumb screws.

 

2.

 

Position jumpers per site engineering instructions

 

3.

 

Replace controller 

-

 secure with 2 thumb screws.

 

Information: Controller 

-

 LAN Port 

-

 Local / Network

 

The LAN port is be configured as Local or Network 

-

 

 

controller display menu path Configuration > Communication Ports > Network Settings > DHCP > mode CLIENT or SERVER

 

Local

 

(Server):  LAN connects to a laptop. 

 

Local (Server) is a temporary setting. When configuration is complete, return LAN port to Network (Client) mode.

 

Network

 

(Client):  LAN connects to a network. (Default).

 

CAUTION:

 

Do not connect LAN port to a network when configured as Local.

 

See 

Pulsar Plus G3 Controller Product Manual

 for details.

 

Information: Controller 

-

 View and Change Parameters and Alarm Severity

 

View and change system parameters and alarm severity 

 

from the factory defaults via:

 

A.

 

Front Display

 

B.

 

LAN port in Local mode via a laptop (web pages)

 

C.

 

LAN port in Network mode (web pages)

 

D.

 

Craft Port via laptop and EasyView2 software or HyperTerminal.

 

EasyView2 (GUI) software can be downloaded from www.gecriticalpower.com.

 

See 

Pulsar Plus G3 Controller Product Manual

 for details.

 

Содержание Integritas 3TL125-SACY-D10Y-P000

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды